Fostex D-108 - Manual (Page 132)

132
D-108 Owner’s Manual (MIDI Implementation Chart/MMC List)
Explanation on the Command/Mode Set
12 22 (): loop on/off command
The command for setting the "loop mode on/off" (=ON/OFF of
AUTO RTN) of D-108. Default figure of the loop operation
mode is "12=stop" and this cannot be changed.
12 28 (): post locate command
The command for setting the "post locate mode" (=ON/OFF of
AUTO PLAY) of D-108.It will stop after locating if "post locate
mode=12." It will enter play after locating if "post locate
mode=15."
12 2D (): auto rec command
The command for setting "auto rec mode on/off" (=ON/OFF of
AUTO PUNCH) of D-108. Upon receiving this command, D-
160 will immediately reply the operating condition by sending
"32 2D ()".
12 41 (): lock enable command
The command for setting "slave mode on/off" (setup menu) of
D-108.
12 42 (): lock mode command
The command for setup of the slave mode (setup menu) when
this equipment is set to "slave mode on."
12 45 () : copy clip command
When this command is received, D-108 will copy (multiple num-
ber of tracks can be copied simultaneously) the sound data, as
data for copy paste, from the pre-registered clipboard-in point
to the clipboard-out point in the track specified by .
With completion of copying the data into the clipboard, D-108
will immediately reply with "32 45 (pleted)>)". If copy cannot be executed due to improper fig-
ures of the pre-registered clipboard in/clipboard out points or
incorrect track section, the corresponding will
be returned.
12 46 (): copy paste command
12 46 (): copy paste com-
mand
When this command is received, D-108 will paste the sound
data which has been copied into the clipboard, on the same
track from the pre-registered auto punch in point as the start-
ing point for the number of time specified by .
However, if the sound data length in the clipboard is less than
10ms, the specifying the will be limited to
"01." Also, by specifying , paste can be executed
on other tracks in mono (in one track units) or stereo units (in
combinations of tracks 1-2, 3-4, 5-6, 7-8).
Since time corresponding to length of the copy clipped sound
data is required to complete the copy paste operation, D-108
immediately replies with "32 46()"
after receiving the command.
Successively upon completing the paste operation, "32 46 (message=01(completed)>)" is transmitted.
If paste cannot be executed due to improper figures of the pre-
registered auto punch in point, insufficient disc capacity, no
sound data in the clipboard, etc., the corresponding sage> will be replied.
12 47 (): erase command
When this command is received, D-108 will erase the data
(writes in "0" data) in the section from the pre-registered auto
punch in point through auto punch out point in the track speci-
fied by . Since time corresponding to length of
the erase section is required to complete the erase operation,
D-108 will immediately reply by "32 47 ((active)>)" after receiving the command.
After the completion of erase operation, "32 47 (sage=01 (completed)>)" will be transmitted.
If erase cannot be executed due to improper figures of the pre-
registered auto punch in point/auto punch out point, incor-
rect track section, etc., the corresponding will
be replied.
12 49: clipboard play command
When this command is received, D-108 will playback once from
the head of the sound data copied in the clipboard by the copy
clip and move clip commands.
Immediately after receiving the command, D-108 will reply
with "32 49 ()."
The sound data track number is indicated by (mmc track>.
Upon completion of playback, "32 49 (pleted) is sent and clipboard play is ended. If there is no sound
data in the clipboard, "32 49 ()"
will be sent and clipboard play operation will be interrupted.
12 4A: undo command
Upon receiving this command, D-108 will revert to the condi-
tion prior to editing copy paste,erase, move paste, cut, redo
operation. With completion of undo operation, D-108 will re-
ply with "32 4A ()."
If D-108 is not possible to undo, "32 4A (message)>)" will be replied.
12 4B: redo command
When this command is received, D-108 will return to the con-
dition prior to undo operation.
With completion of redo operation, D-108 will reply with "32
4B ()."
If D-108 is not possible to redo, "32 4B (message)>)" will be replied.
12 4D (): move clip command
When this command is received, D-108 will copy (multiple
tracks can be copied simultaneously) the sound data from the
pre-registered clipboard in point to the clipboard out point, as
data for move paste operation. With completion copying the
data into the clipboard, D-108 will immediately reply with "32
4D ()." If copy cannot be ex-
ecuted by the reason of pre-registered improper clipboard in/
clipboard out point figures or incorrect track section, etc., the
corresponding will be replied.
12 4E (): move paste command
12 4E (): move paste com-
mand
When this command is received, D-108 will paste the sound
data which have been move clipped in the clipboard, for the
number of times specified by on the same track
from the pre-registered auto punch in point as the starting
point. At the same time, the move clipped original sound data