Fostex D-108 - Manual (Page 134)

134
D-108 Owner’s Manual (MIDI Implementation Chart/MMC List)
14 02 (): Tempo set command
The command for tempo set of this equipment. If a new data is
registered in a bar/meter where data already exists, the former
data will be written over. When this command is received, this
equipment will reply with "34 02 ()." Upon
completing the registeration, will reply with
"01 (completed)," or with "10 (over value error)" if registeration
is attempted at a non-existing point or an erroneous figure is
used.
14 03 : Tempo map all erase command
When this command is received, this equipment will erase all
meter and tempo data in the current program and thus return
it to the default state (meter=4/4, tempo: =120). Also, when
this command is received, this equipment will reply with "34
03 ()." Upon completing the registeration, message> will reply with "01 (completed)," or with "10 (over
value error)" if registeration is attempted at a non-existing point
or an erroneous figure is used.
14 04 (): Preroll time set command
The command for setting the current program preroll time at
the figure indicated by .
14 06 (): Frame rate set command
The command for setting the current program frame rate at
the figure indicated by .
14 07 (): Fs rate set command
The command for setting the current program fs (sampling
frequency) at the figure indicated by .
14 08 (): Time base set command
The command for setting the current program time base of
this equipment to that indicated by .
The Status Request Command
22 21: loop operation status request
The command inquiring the loop operation mode setup sta-
tus. D-108 will reply with "32 21 ()."
22 22: loop on/off status request
The command inquiring the loop on/off (=ON/OFF of AUTO
RETURN) setup status. D-108 will reply with "32 22 (off>)."
22 28: post locate status request
The command inquiring the post locate mode (ON/OFF of AUTO
PLAY) setup status. D-108 will reply with "32 28 (mode>)".
22 2D: auto rec status request
The command inquiring the auto rec mode setup status and
this is replied by "32 2D ()." Reply from D-108
against this status request will be either one of the following:
=05: Possible to undo rehearsal mode.
=06: Possible to undo take mode.
=72: off
22 41: lock status request
The command inquiring the slave on/off setup status and the
lock status. D-108 will reply with "32 41 ()."
22 42 : lock mode status request
The command for inquiring the lock mode setup status and
this is replied with "32 42 ."
22 45: copy clip status request
The command inquiring the clipboard condition. If there is a
copy paste data in the clipboard, D-108 will reply with "32 45
()." If data in the clipboard is for move
paste or there is no valid data in it, it will reply will "32 45
()."
22 46: copy paste status request
The command inquiring execution status of copy paste edit-
ing. When this command is received, D-108 will reply with
either "32 46 ()" or "32 46 (message=00>)." indicates unprocessed time un-
til completion.
22 47: erase status request
The command inquiring execution status of erase.
When this command is received, D-108 will reply by either "32
47 ()" or "32 47 (sage=00>)." indicates unprocessed time until
completion.
22 4D: move clip status request
The command inquiring the clipboard status. If there is a move
paste data on the clipboard, D-108 will reply with "32 4D (message=01>)." If data in the clipboard is for copy paste or
there is no valid data on it, "32 4D (data)>)" will be replied.
22 4E: move paste status request
The command inquiring the move paste execution status.
When this command is received, D-108 will reply with "32 4E
()" or "32 4E (sage=00>)." indicates unprocessed time until
completion.
23 41: digital in channel status request
23 41: adat in channel status request
The command inquiring the digital in channel setup status.
When this command is received, D-108 will reply with "33 41
()" or "33 41 (track>)."
23 42: digital out channel status request
23 42: adat out channel status request
The inquiring the digital out channel setup status.
When this command is received, D-160 will reply with “33 42
()” or “33 42 ().
23 43: program status request
The command inquiring the presently operating program num-
ber. When this command is received, D-108 will reply with
"33 43 ()."
23 44: click on/off status request
The command inquiring the metronome on/off status of D-
108. When this command is received, D-108 will reply with
"33 44 ()."