HP ProLiant xw460c Blade Workstation Instruction Manuals and User Guides
We have 4 Instruction Manuals and User Guides for ProLiant xw460c Blade Workstation HP
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 33 |
| Size: | 1.06 MB |
Show table of contents
Document Outline
- HP BIOS Serial Console User Guide
- Notice
- Contents
- Console Redirection Overview
- HP BIOS Serial Console/EMS Support Settings and Configuration
- Terminal Emulation Programs
- Acronyms and Abbreviations
- Index
| Recognized languages: | English |
|---|---|
| Pages: | 93 |
| Size: | 2.93 MB |
Show table of contents
Document Outline
- HP ProLiant BL460c Server Blade User Guide
- Notice
- Contents
- Component identification
- Operations
- Setup
- Hardware options installation
- Cabling
- Software and configuration utilities
- Server blade deployment tools
- Configuration tools
- Management tools
- Automatic Server Recovery
- ROMPaq utility
- Integrated Lights-Out 2 technology
- Erase Utility
- StorageWorks library and tape tools
- HP Systems Insight Manager
- Management Agents
- HP ProLiant Essentials Virtualization Management Software
- HP ProLiant Essentials Server Migration Pack - Physical to ProLiant Edition
- HP BladeSystem Essentials Insight Control Data Center Edition
- Redundant ROM support
- USB support and functionality
- Diagnostic tools
- Remote support and analysis tools
- Keeping the system current
- Troubleshooting
- Battery replacement
- Regulatory compliance notices
- Regulatory compliance identification numbers
- Federal Communications Commission notice
- Declaration of conformity for products marked with the FCC logo, United States only
- Modifications
- Cables
- Canadian notice (Avis Canadien)
- European Union regulatory notice
- Disposal of waste equipment by users in private households in the European Union
- Japanese notice
- BSMI notice
- Korean notice
- Laser compliance
- Battery replacement notice
- Taiwan battery recycling notice
- Electrostatic discharge
- Specifications
- Technical support
- Acronyms and abbreviations
- Index
| Recognized languages: | English |
|---|---|
| Pages: | 58 |
| Size: | 1.05 MB |
Show table of contents
Document Outline
- HP GbE2c Ethernet Blade Switch for c-Class BladeSystem User Guide
- Notice
- Contents
- Introduction
- Overview
- Additional references
- Features
- Switch architecture
- Supported technologies
- Layer 2 switching
- IEEE 802.1 Q-based VLAN
- Spanning Tree Protocol
- SNMP
- Port mirroring
- Port trunking and load balancing
- TFTP support
- Store and forward switching scheme
- BOOTP
- NTP
- RADIUS
- TACACS+
- SSH and SCP
- XModem
- IGMP Snooping
- Jumbo frames
- Auto-MDI/MDIX
- Auto-negotiation of duplex mode and speed
- Redundant images in firmware
- External components
- Installing the switch
- Replacing and upgrading the switch
- Regulatory compliance notices
- Technical specifications
- Performing a serial download
- SNMP MIBs support
- Electrostatic discharge
- RJ-45 pin specification
- Troubleshooting
- Forgotten administrator user name and password that was configured on the switch
- Health LED on the switch is not on
- Health LED on the switch stays amber for more than 30 seconds and switch does not boot
- No link LED appears, even after plugging the Category 5 cable in the RJ-45 connector of the external port
- Cannot access the switch serial console interface using null modem connection from a PC Terminal Emulation Program
- Error message that the switch failed to complete the system self-testing appears on the serial console screen
- The switch fails to get its IP settings from the BOOTP server, even though by default it is configured for BOOTP
- The keyboard locks up when using HyperTerminal to log on to the switch through the console interface
- Cannot connect to the switch console interface remotely using Telnet
- Password is not accepted by the switch using the remote console interface immediately after a reboot
- Cannot connect to the switch console interface remotely using SSH
- Cannot connect to the switch SNMP interface
- The port activity LEDs continuously indicate activity after connecting more than one port to another switch or destination device
- Cannot connect to the switch remotely using the Web interface
- Cannot enable a port in multiple VLANs while configuring VLANs
- The switch does not let the user enable two adjacent ports into two different VLANs while assigning the ports to VLANs
- While using TFTP to download firmware, the switch fails to connect to the TFTP server, or after connection the download fails
- The switch fails to connect to the TFTP server while using TFTP to download or upload a configuration file, or after connection the download or upload fails
- The console screen displays a message to change the baud for the terminal emulation session for XModem transfer after forcing the switch into the download mode, and does not display CCCC...
- The download fails after starting to download the firmware file
- The switch configuration is corrupt
- Acronyms and abbreviations
- Index
| Recognized languages: | English |
|---|---|
| Pages: | 155 |
| Size: | 3.56 MB |