beautypg.com

Sealey VSE5580 User Manual

Vse5580, Rear subframe bush tool - bmw 5 series, Fig.1

background image

INSTRUCTIONS FOR:

REAR SUBFRAME BUSH

TOOL - BMW 5 SERIES

Model No:

VSE5580

1.

SAFETY INSTRUCTIONS

2.

INTRODUCTION & APPLICATIONS

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give

you years of trouble free performance.

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE TOOL CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

WARNING! Ensure Health and Safety, local authority and general

workshop practice regulations are adhered to when using tools.

DO NOT use tools if damaged.

Maintain tools in good and clean condition for best and safest

performance.

Ensure that a vehicle which has been jacked up is adequately

supported with axle stands and that the wheels are chocked,

refer to the vehicle manufacturer’s service instructions, or a

proprietary manual.

Wear approved eye protection. A full range of personal safety

equipment is available from your Sealey dealer.

Wear suitable clothing to avoid snagging. Do not wear jewellery

and tie back long hair.

DO NOT use air tools to operate the force screw.

IMPORTANT: The force screw must be kept well lubricated.

IMPORTANT: This manual is provided as a guide only, refer to

the vehicle manufacturer’s service instructions, or a proprietary

manual, to establish the current procedure and data.

WARNING! Failure to heed safety and warning instructions may

result in damage and/or personal injury and will invalidate the

warranty.

WARNING! The warnings, cautions and instructions referred

to in this manual cannot cover all possible conditions and

situations that may occur. It must be understood that

common sense and caution are factors which cannot be

built into this product, but must be applied by the operator.

Suitable for the removal / installation of the rear axle carrier bushes.

Can be used in situ without the need to remove the rear subframe

assembly from the vehicle. Use the tool with a 24mm spanner only.

Applications:

BMW:

E39 5 Series Saloon (95 - 05)

.

OEM Bush No 33311091422

3. OPERATION

NOTE! Illustration of the sub frame removed from the vehicle for

clarity. Refer to the vehicle manufacturer’s service instructions, or

a proprietary manual to carry this out.
NOTE! This tool will insert the bush to the correct depth, but

before installing the new bush, refer to the vehicle

manufacturer’s service instructions, or a proprietary manual, to

establish the correct horizontal alignment/positioning of the bush.

IMPORTANT: This tool is designed to aid removal of the bush.

We suggest that the area around the bush is thoroughly

cleaned.

The threads of the tool should also be thoroughly lubricated in use.

An Impact Socket must NOT be used with this tool.

Stripped threads and bent thrust cups are not accepted

warranty claims on this tool.

3.1. Removing Bush

3.1.1. Assemble the removal (black) set as in Fig.3. Thread the

Adaptor (A) onto the short threaded end of the bolt (F) with the

boss adjacent to thread shoulder. Pass the bolt through the bush

from above, rotate to register machined flats and then position

the barrel Adaptor (B) over the bolt. Fit the barrel Adaptor (B)

against the housing face with the recess fitted over the location

on the bush and or housing. Thread the ball race nut (E) on

to the projecting bolt and wind it up to the barrel Adaptor (B) flat

face with ball race leading. Check axis alignment prior to full

force extraction.

ALWAYS KEEP FORCE SCREW

WELL LUBRICATED. MOLYBDENUM/

COPPER BASED RECOMMENDED.

DO NOT USE AIR TOOLS OR

IMPACT SOCKET.

Original Language Version

VSE5580 Issue: 1 - 22/10/12

Force screw maximum load 150Nm. Exceeding this load will

shorten the life of the force screw. The force screw is considered

to be a consumable item and is NOT covered under warranty.

© Jack Sealey Limited

Rear of vehicle

Vehicle subframe illustration only

Flanged bush

Fig.1

Component

location &

carry case.

Fig.2

Housing

boss (4x)

This manual is related to the following products: