Sealey VSE210 - Manual

1.1 FUEL SAFETY
p WARNING! Ensure Health and Safety, local authority, and general workshop practice regulations are adhered to when working with
fuel injection systems and petrol in general.
p WARNING! Petrol fumes and battery gases are explosive, DO NOT smoke or allow an open flame or sparks in the work area.
1.1.1 FUEL LEAKS
3 Keep a dry chemical (class B) fire extinguisher near to the work area.
3 Avoid fire hazard by using caution when disconnecting fuel lines and installing adaptors, as some spillage is inevitable.
3 When connecting, or disconnecting from a fuel system, relieve pressure from system and wrap a cloth around the fuel line fitting to absorb any
fuel leakage. Constantly check gauge and adaptor connections for leaks. If you see leakage turn off the ignition or disable the fuel pump,
relieve fuel pressure if necessary and correct leaks before continuing.
3 When using ‘tee’ adaptors, secure hose with hose clamps to ensure leak-free connections.
3 Check all adaptor sealing washers and 'O' rings are in good condition before use.
3 When connecting hose coupler to Test Port, Tee and In-Line Banjo Bolt Adaptors ensure coupler is correctly seated onto adaptor.
7 DO NOT let fuel spill onto a hot engine.
7 DO NOT allow fuel to remain in the adaptors or hoses after use. To clear any fuel trapped in the gauge/hose assembly after use, hold gauge
vertical with hose coupler end in suitable fuel container. Depress coupler valve stem and at the same time, depress pressure relief button
situated under the gauge.
p WARNING! Wipe up fuel spills immediately.
1.2 GENERAL
p WARNING! Exhaust gas contains deadly poisonous gases. Test area must well ventilated - route exhaust gas outdoors.
3 Maintain tools in good and clean condition for best and safest performance.
3 If required, ensure the vehicle to be worked on is adequately supported with axle stands, ramps and chocks.
3 Before performing a test with the engine running (unless the manufacturer's manual states otherwise), set the parking brake and place the gear
selector in neutral or park, and block the drive wheels.
3 Before repairing the fuel system, turn off the ignition switch and disconnect the battery per manufacturer's procedure. Never disconnect the
battery while the engine is running.
3 Wear approved safety goggles. A full range of personal safety equipment is available from your Sealey dealer.
3 Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
3 Keep yourself, clothing and test equipment away from all moving or hot engine parts.
7 DO NOT use tools if damaged.
7 DO NOT use the components from this kit on diesel fuel systems.
3 Account for all tools being used and do not leave them in or near the engine.
3 IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or proprietary manual to establish the current procedure and data.
These instructions for use are provided as a guide only.
VSE210 - 1 - 211204
2. INTRODUCTION
Comprehensive kit of adaptors and fittings for modern fuel injection systems.
Components fitted with quick coupling system and safety valve to prevent
inadvertent discharge of fuel under pressure. Kit supplied with large high pressure
gauge reading 0-145psi and 0-1000kpa and a small low pressure gauge for
accurate low pressure readings. Pressure release valve fitted with long drain hose
allows safe recovery of fuel. Supplied in carry-case.
1. SAFETY INSTRUCTIONS
INSTRUCTIONS FOR:
FUEL INJECTION
PRESSURE TEST KIT
MODEL:
VSE210
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without
prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from purchase date,
proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and
leave your full name and address, including postcode.
www.sealey.co.uk 01284 757500 01284 703534
[email protected]
Web
email
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.