Fig.2 fig.1 fig.3, Maintenance 5. declaration of conformity, Declaration of conformity – Sealey WRP1600 User Manual
Page 2: Operating instructions
4.
MAINTENANCE
5.
DECLARATION OF CONFORMITY
4.1.
CLEANING
Clean the puller after each use and wipe with a slightly oiled cloth. Store in a safe, dry, childproof location.
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed here are in
conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
WIRE ROPE PULLERS
Models
WRP800, WRP1600,
WRP3200
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
18th August 2006
Signed by Mark Sweetman
WRP800, WRP1600, WRP3200 - 2 - 180806
3.
OPERATING INSTRUCTIONS
"
WARNING! Ensure that you read, understand and apply Section 1 Safety Instructions before using the puller.
"
WARNING! Before every use thoroughly inspect every part of the wire puller for signs of damage or stress. If any are found
do not use but refer to an authorised repair agent for all repairs. Do not use the wire rope if there is any evidence of fraying,
stress or other damage. Do not kink the wire rope.
3.1.
ATTACHING PULLER TO LOAD AND ANCHOR
3.1.1
Pass the anchor pin through the puller body (fig.1). When it is as far as it can go rotate through a further 180° and insert fully home.
A ‘D’ pin (not supplied) may be pushed through the anchor pin to provide additional security.
3.1.2
Attach the puller to a suitable anchor point, ensuring that it is capable of withstanding the maximum line pull, check any chains, strops
or shackles to ensure they are rated equal to or exceeding the maximum line pull. Do not wrap the wire rope back on itself.
3.2
INSERTING WIRE ROPE.
3.2.1
Place forward and reverse levers away from the release lever. Push the release lever into the locked position as shown in fig 2.2, this
allows the internal jaws to open, enabling the wire rope to be inserted through the wire feed (fig 2.1).
Note: The release lever can be difficult to lock into place, it requires firm pressure downwards onto it (the forward and reverse
levers will be seen to move out), before also pushing forwards to lock it into place. This is best carried out with the puller
tipped up at an angle (see fig.3).
3.2.2
Insert the wire rope through the feed (fig 2.1). Direct the wire rope out of the back and run above the anchor pin.
3.2.3
Take up slack by pulling the cable through the puller. When the slack has been taken up unlock the release lever by pushing down
and back. The puller is now ready for use.
3.3
OPERATION
3.3.1
PULLING A LOAD
3.3.2
To pull a load, ensure the wire rope is firmly attached to the load to be pulled and the puller is anchored to a suitable position.
3.3.3
Lock the handle onto the forward lever (fig 2.4) by locating the pin and twisting through 180°.
3.3.4
Moving the handle back and forth will pull the wire rope through the puller.
NOTE: As an added safety feature the forward lever is fitted with a shear pin. If the load is greater than the capacity of the puller the
pin will shear. The pin will require replacing with part No. WRP800.16, WRP1600.16 or WRP3200.16.
3.4
LOWERING A LOAD
3.4.1
To lower a load, lock the handle onto the reverse lever (fig 2.3), by locating the pin and twisting through 180°.
3.4.2
Moving the handle back and forth will push the wire rope back through the puller.
3.4.3
When all load has been removed from the puller, move the release lever back into the locked position (see 3.2.1.above) and withdraw
the wire rope from the puller.
3.4.4
Wind the wire rope back onto its reel, take this opportunity to inspect the rope for any damage that may have occurred during the
pulling procedure. Unlock the release lever on the puller, if not being used, store away in a safe, dry, childproof location
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
fig.2
fig.1
fig.3