Sealey 2000ESLE - Manual (Page 3)

7. TROUBLE SHOOTING
IMPORTANT: MAINTENANCE OR REPAIR Of HYDRAULIC SYSTEMS MUST ONLY BE PERfORMED BY A QUALIfIED PERSON.
PROBLEM POSSIBLE CAUSE REMEDY
Jack will not lift the load 1) Overloaded
2) Oil level low
3) Release valve not correctly closed
4) Air in system
5) Piston rod not functioning
6) Packing worn or defective
1) Be sure to use jack with adequate capacity
2) Top up oil level
3) Check and close release valve (fig.2)
4) Open release valve and pump the handle a few times.
Close valve and re-try (fig.2 and fig.1)
5) Clean and replace oil
6) Replace packing
Jack does not lift high enough or feels
“spongy”
1) Oil level too high or too low
2) Worn seals
3) Air in system
4) Release valve not closed
1) Fill or remove excess oil
2) Return jack to local service agent
3) Open release valve and pump the handle a few times.
Close valve and re-try (fig.2 and fig.1)
4) Check and close release valve (fig.2)
Jack lifts poorly 1) Pump packing or valves malfunctioning
2) Oil is dirty
3) Air in the system
1) Replace packing and/or clean valves
2) Replace oil
3) Open release valve and pump the handle a few times.
Close valve and re-try (fig.2 and fig.1)
Jack lifts but will not hold load 1) Release valve partially open
2) Dirt on valve seats
3) Air in system
4) Faulty seals
5) Packing worn or defective
1) Check and close release valve (fig.2)
2) Lower jack, close release valve. Place foot on front wheel
and pull up lifting arm to it’s full height by hand.
Open the release valve to lower arm (fig.2)
3) Open release valve and pump the handle a few times.
Close valve and re-try (fig.2 & fig.1)
4) Replace packing or contact local service agent
5) Replace packing
Jack will not lower completely 1) Unit requires lubrication
2) Piston rod bent or damaged
3) Jack frame/link system distorted due to
overloading/poor positioning
4) Air in system
5) Release valve partially closed
6) Jack spring damaged or unhooked.
1) Oil all external moving parts
2) Contact local service agent
3) Replace damaged parts or contact local service agent
4) Open release valve and pump the handle a few times.
Close valve and re-try (fig.2 & fig.1)
5) Check and fully open release valve (fig.2)
6) Replace spring or contact local service agent (fig.4 and fig.5)
Jack does not lower at all 1) Release valve closed 1) Check position of handle twist mode (fig.2) and fully open release valve.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INfORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [email protected] or phone 01284 757500.
Original Language Version 2000ESLE/3000ESLE Issue: 1 - 10/04/14 © Jack Sealey Limited
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Jack fully elevated
Rubber
saddle
Removable
tool tray