Sealey 3012CXD - Manual

3.1 ASSEMBLY
3.1.1 The jack comprises the following parts:
Steel chassis.
Two-part pumping handle with bolt.
3.1.2 Insert the upper handle into the lower handle. Secure the
two pieces together with the bolt (A). (Fig.1).
3.1.3 Undo the handle socket screw (B) until it no longer
protrudes into the handle socket (Fig.2).
3.1.4 Insert the pump handle into the handle socket, engaging the
square drive of the release valve.
3.1.5 Ensure that the handle is correctly inserted into the socket,
then tighten the handle socket screw (B).
InSTrUcTIon MAnUAL For:
TROLLEY JACK 3TONNE ROCKET
LifT
ModEL no:
3012CXD
Your new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Important: READ ThESE iNSTRuCTiONS CAREfuLLY. NOTE ThE SAfE OPERATiONAL REQuiREMENTS, WARNiNGS AND CAuTiONS. uSE
ThiS JACK CORRECTLY AND WiTh CARE fOR ThE PuRPOSE fOR WhiCh iT iS iNTENDED. fAiLuRE TO DO SO MAY CAuSE DAMAGE AND/
OR PERSONAL iNJuRY AND WiLL iNvALiDATE ThE WARRANTY. RETAiN ThESE iNSTRuCTiONS fOR fuTuRE uSE.
1. SAfETY PRECAuTiONS
2. iNTRODuCTiON / SPECifiCATiON
3. ASSEMBLY
 Ensure the jack is in sound condition and good working order.
Take action for immediate repair or replacement of damaged
parts. Use genuine parts only. The use of improper parts may be
dangerous and will invalidate the warranty.

Locate the jack in a suitable, well lit working area.
 Keep working area clean and tidy and free from unrelated
materials.

Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in.

chock wheels of vehicle.
 Ensure the vehicle handbrake is engaged, engine is switched off
and transmission is in gear (or “PArK” if automatic).

Ensure minimum distance of 0.5m between vehicle and static
objects such as doors, walls, etc., to allow for vehicle tilting.
 Ensure all non-essential persons keep a safe distance whilst the
jack is in use.

Ensure there are no passengers in the vehicle.
 Place jack under only those lifting points recommended by
vehicle manufacturer (see vehicle handbook).

check that the lifting point is stable and centred on the jack
saddle.

Ensure the jack wheels are free to move and that there are no
obstructions.

DanGEr: Use the jack for lifting only, not for supporting the
lifted load.

Ensure there are no persons or obstructions beneath the vehicle
before lowering.

Use suitable axle stands under the vehicle before proceeding with
any task.

Use a qualified person to lubricate and maintain the jack.
 Ensure that only hydraulic jack oil is used in the jack.
 DO NOT operate the jack if damaged.
 DO NOT allow untrained persons to operate the jack.
 DO NOT exceed the rated capacity of the jack.
 DO NOT allow the vehicle to move during lifting or lowering, or
use the jack to move the vehicle.

DO NOT jack vehicle if there is a risk of spillage of fuel, battery
acid, or other dangerous substances.

DO NOT work under the vehicle until appropriately rated axle
stands have been correctly positioned.

DO NOT use the jack for purposes other than that for which it is
intended.

DO NOT top up hydraulic system with brake fluid. Use hydraulic
jack oil only. (Sealey Part no: HJo500MLS or HJo5LS)

DO NOT adjust the safety overload valve.
 When not in use store jack, fully lowered, in a safe, dry, childproof
area.
Model No: ...........................................................................3012CXD
capacity ...............................................................................3tonne
Minimum saddle height ........................................................145mm
Maximum saddle height .......................................................520mm
Maximum chassis height .....................................................160mm
4. hYDRAuLiC SYSTEM PuRGiNG
4.1 open the release valve by turning it one full turn
counter-clockwise.
4.2 Pump the handle a minimum eight full strokes.
4.3 close the release valve by turning it clockwise.
Single piece hydraulic unit with heavy base design and large jacking
saddle. Universal joint release mechanism allows safer, more
controlled lowering of the jack. double pump 'rocket Lift' feature
brings lifting arm straight into contact with the jacking point in 1-2
strokes. Fitted with safety overload valve and 'pump-through' valve
to prevent handle locking at maximum ram. Suitable for loaded vans
up to 3.5 tonne GVW.
Original Language Version 3012cXd Issue: 1 - 15/08/11
fig.1
fig.2
Length ............................................................................. 670mm
Weight ............................................................................. 39.5kg
optional rubber Jack Pad .............................................. 3000cXd/JP