Sealey WF10Q - Manual (Page 2)

Page 2
3. SAFETY/OPERATING INSTRUCTIONS
3.2 OPERATION. (Refer to Section 4.3 (a) regarding inspection before each and every use).
a) Always use the jib in its retracted position where the capacity is greatest, whenever possible. Extend the jib only when
necessary to reach the load. When changing the position of the jib extension, place the jib in the horizontal position to prevent it
sliding in or out and always remember to replace the locking pin and tighten the locking bolt. Be sure that the load is within the
rated capacity for the particular jib position selected.
b) Remove the pump handle from its stowage position on the main upright. Slide it into the pump socket and commence pumping. The
jib will start to move upwards. Continue to pump until the jib reaches the height at which the load can be secured.
c) Connect the crane hook to the load using a suitable sling or support beam. Be aware of the load weight, and check that it is within
the capacity of the crane (at the jib extension you are using) and the sling or support beam. When removing engines ensure the
weight is known. Use only the lifting points recommended by the vehicle manufacturer.
d) Lift only from directly above the load. WARNING! DO NOT LIFT THE LOAD AT AN ANGLE!
e) To lower the load turn the release valve VERY SLOWLY anti-clockwise until the jib starts to move slowly downwards. The rate of
descent can be controlled by fine movements of the release valve handle. Avoid sudden twisting movements.
WARNING! DO NOT allow the load to drop suddenly.
f) The crane is not a transportation device but may be used to reposition the load being worked on. To do so, lower load and jib
with care, to the lowest possible point before attempting to move. DO NOT try to move crane in a sideways direction. The crane is
not designed to support the load indefinitely. When the load has been repositioned, lower the load onto a secure and appropriate
working base, being fully aware of your own and other persons locations in relation to the lowering load.
g) When load has been secured, remove lifting sling, support beam etc. and place crane in a safe location with lifting beam fully
lowered.
NOTE: ENSURE YOU HAVE READ AND UNDERSTOOD THE SAFETY INSTRUCTIONS AT THE BEGINNING OF THIS SECTION BEFORE YOU
OPERATE THE CRANE.
3.1 SAFETY
3
Keep crane, lifting slings, support and beams in good working order and condition. Follow the inspection requirements as described in
Section 4 page 2 Maintenance. Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all
accessory lifting devices are suitably certified. If crane is damaged, remove from service immediately.
3 Ensure the surface on which the crane is used is level, firm and capable of supporting the weight of the crane with maximum
load - we recommend concrete. Never use the crane on tarmacadam or other soft surfaces.
3 Ensure the crane legs and arms are locked before use.
3 Keep children and unauthorised persons away from the working area.
3 Keep working area clean and tidy, free from unrelated materials and ensure that there is adequate lighting.
3 Ensure that load does not exceed the maximum lifting capacity of the crane. Overloading the crane is dangerous. Where
appropriate, use only the lifting points recommended by the manufacturer of the item to be lifted, e.g. vehicle engine.
3 Before lifting the load ensure that the crane jib is in the lowest practical position, that there are no obstacles which may snag the load
whilst it is being lifted and that the area above the jib is clear.
3 To avoid injury, be fully aware of your own and other persons locations in relation to the lifting and lowering, of the load.
3 Keep a sound footing and balance, and ensure the floor is not slippery.
3 Ensure jib extension locking bolt and nut are in position before lifting.
3 Ensure the centre of gravity always remains inside the crane base.
7 DO NOT harness the load at an angle or use any attachments not verified as fit for purpose.
7 DO NOT allow the load to swing during lifting.
7 DO NOT allow the load to drop suddenly. Lower load with care, ensuring that you are fully aware of the condition of the surface onto
which the load is to be placed.
7 DO NOT load crane beyond its rated capacity for each specified jib extension position as indicated in Section 2 page 1.
The capacity of the crane reduces as the jib is extended.
7 DO NOT position any part of your body beneath the load.
7 DO NOT use the crane to move or transport a load other than for repositioning (see 3.2.f). The crane is a lifting device only.
7 DO NOT apply any sideways pressure to any part of the crane during lifting or when a load is suspended.
7 DO NOT attempt to adjust the safety valve, which has been set and sealed by the manufacturer.
7 DO NOT use this product to perform a task for which it is not designed.
7 DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.
7 DO NOT climb on the crane.
3 When not in use fold the crane down and store in a safe, dry, childproof area.
3 This crane is designed for lifting within a garage or workshop environment.
 WARNING! Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the
warranty.
NOTE: The crane MUST be kept clean and dry and must be maintained in accordance with these instructions.
4.1. Lubrication.
a) Oil all working parts monthly.
b) The ram is filled with oil and should only require occasional topping up. For the occasional top up DO NOT use brake fluid, as this will
damage the hydraulic seals. Proceed as follows:
1) Use only good quality hydraulic jack oil available from your supplier.
2) DO NOT OVERFILL as this will cause failure
,
with ram in lowered position remove rubber bung located on the ram and top up to
just below the filling hole. Replace rubber bung.
3) After filling with hydraulic oil, pump the crane up to full height and pour off any excess oil.
4.3. Inspection and Examination of Crane Before Use.
a) Before each use of the crane, perform an inspection for leaks, damage, loose or missing parts.
b) The workshop crane must be examined immediately if it has been subject to an abnormal load or shock. It is recommended that such
an examination is made by an authorised service agent.
c) The owner and/or operator must be aware that repair of this equipment will require specialised knowledge and facilities.
It is recommended that an annual examination of the workshop crane is made by an authorised service agent.
d) Unauthorised parts may be dangerous and will invalidate the warranty.
4. MAINTENANCE/EXAMINATION/INSPECTION
Original Language Version
WF10Q Issue: 3(I) - 09/12/14 © Jack Sealey Limited