Sealey SB997 - Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION

WARNING! Turn off, or disconnect from, air supply before servicing or performing any maintenance and when unit is not in use.
Failure to comply with this instruction may damage the unit and will invalidate your warranty.

WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety equipment
is available from your Sealey dealer.

Maintain correct balance and ensure firm footing.
 Spillages of abrasive material, which may be slippery, must be cleaned up immediately to avoid injury.

Locate blaster in a suitable, well ventilated, work area. Keep area clean and tidy and free from unrelated materials, and ensure that
there is adequate lighting.

Maintain the blaster in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the warranty.

Keep the unit clean for best and safest performance.

Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.

Always keep the blast nozzle directed at the workpiece.

If a failure or malfunction occurs disconnect from air supply immediately.

Keep all other persons away from the working area. Contact with high pressure blast or inhaling the dust generated is dangerous.

DO NOT use the blaster for any purpose other than that for which it is designed.

DO NOT operate the blaster if any parts are missing or damaged as this may cause failure and/or personal injury.

DO NOT use any abrasive which contains free silica. We recommend Sealey Shot Blasting Grit, item B/25KG.

DO NOT attempt to clear a blocked nozzle while the unit is pressurised.

DO NOT allow untrained persons to operate the blaster.

DO NOT get the blaster wet or use in damp or wet locations or areas where there is condensation.

DO NOT leave the blaster operating unattended.

DO NOT operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication.

DO NOT stand or sit on the blaster.

DO NOT direct air from the air hose at yourself or others.

DO NOT operate system with air supply exceeding 125psi.
INSTRUCTIONS FOR:
SHOT BLASTERS WITH WATER TRAP AND
WHEELS 37/75ltr
MODEL No's:
SB997 & SB998
4. AIR SUPPLY
 WARNING! Ensure the air supply does not exceed 125psi while
operating the unit. Too high an air pressure will shorten the life of the unit
owing to excessive wear and may cause damage and/or personal injury.
4.1. Ensure the blaster air valve (trigger) is in the ‘Off’ position before
connecting to the air supply.
4.2. Keep the air hose between the compressor and the unit a reasonable
length and install an air filter and water separator (fig.1).
4.3. Drain the air tank daily. Water in the air line will damage the unit.
4.4. The recommended hook-up procedure is shown in fig.1.
4.5. The minimum hose diameter should be 1/4" I.D. and fittings must
have the same inside dimensions.
4.6. Use correct hoses and fittings.
4.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear
and ensure that all connections are secure.
Pressured tank for maximum power with 2.4mtr rubber hose, four ceramic nozzles and in-line water trap for moisture-free grit blasting.
Supplied with bayonet air line coupling and air flow regulator. Accepts a variety of grits up to 700microns and suitable for stripping rust and
paint from wheels, chassis, panels and other corroded/painted surfaces.
Model: SB997 SB998
Maximum Fill Weight: 46kg 92kg
Working Pressure: 60 ~ 125psi
Air Requirements: 6 ~ 25cfm
Air Inlet Size: 1/4” BSP
Nozzle Sizes: 2, 2.5, 3, 3.5 & 5mm
Maximum Grit Size: 700microns
Maximum Grit Consumption: 180kg/hr
fig.1
SB997
Original Language Version
Refer to
Instructions
Wear Eye
Protection
Wear Protective
Gloves
SB997, SB998 Issue: 4(SP) -09/02/15 © Jack Sealey Limited