Sealey YK509FAH - Manual (Page 4)

Declaration of Conformity We, the sole importer into the uK, declare that the products listed below are in conformity with the following
EEc standards and directives.
The construction files for these products are held by the Manufacturer
and may be inspected on request by contacting Jack Sealey Ltd
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery
Air Hydraulic Floor Press Models
YK509FAH
YK759FAH
2006/42/Ec Machinery Directive
93/68/EEc cE Marking Directive
Signed by Mark Sweetman 2nd September 2008
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole uK Distributor,
Sealey Group,
Bury St. Edmunds,
Suffolk.
01284 757500
[email protected] 01284 703534
e-mail
Web
www.sealey.co.uk
6. DECLARATION OF CONFORMITY
5. MAINTENANCE
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE PRESS.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose
of the product and the oil according to local regulations.
YK509FAH & YK759FAH Issue no: 1 - 02/09/08
Note: Maintenance and repair must only be carried out by qualified person. contact your Sealey dealer for details.
5.1 Always keep the press clean, dry and lubricate all moving parts at regular intervals.
5.2 When not in use always store in a dry location with the piston retracted.
5.3 Should you need to check or replace oil ensure piston is fully retracted. Remove the oil reservoir filler plug and top up using Sealey
hydraulic jack oil. DO NOT use brake fluid. contact your local Sealey dealer for details. After filling purge the system to remove any air.
Fig.4 Fig.5
 DANGER! Press's are purpose designed to withstand greater loads than
the hydraulic units can develop. For safety reasons, always ensure the
workpiece is secured on the table to ensure loads that flex will not
suddenly “give” causing danger to operator or damage to component.
Ensure you have read and understood chapter 1 safety instructions.
4.2 OPERATING INSTRUCTIONS.
4.2.1 connect the air valve to the air supply.
4.2.2 Set the bed frame at the desired height, if adjustment is required, turn
the hand winch until the cable just takes the weight of the bed frame,
remove the safety clips (13) from the back of the pins (12), see Fig.4 and
withdraw the pins. use the hand winch to raise or lower the bed frame to
the height required, insert pins and safety clips (Fig.5). Slacken off the
hand winch so that the pins are taking the full weight of the bed frame.
4.2.3 check that the release valve on the hydraulic unit is fully closed, ready
for operation.
4.2.4 Locate the flat pressing plates or the v-blocks on to the bed frame, push
down the locating pins to ensure the plates do not slip. Place workpiece
onto the plates and position the head of the hydraulic unit on the centre
of the workpiece using an appropriate extension. Note: care must be
taken to ensure the plates do not fall from the bed frame.
 WARNING! DO NOT apply off centre loads.
4.2.5 When work is complete turn the release valve anti-clockwise to release
the pressure and the piston and the ram head will retract automatically.
Note: Always keep the piston retracted after use.
4.2.6 Disconnect the air valve from the air supply.
YK759FAH