Sealey S0530 - Manual (Page 2)

 WARNING! Ensure that the grinder is unplugged from the mains power supply before assembling.
3.1. Fit Grinding Disc (only to be performed by person holding grinding wheel certificate)
3.1.1. Place the disc flange ( fig.5.8) onto the centre spindle (fig.5.A) ensuring that the joint ring (fig.5.9) is facing away from the grinder.
Engage the recess in the disc flange with the drive flats on the shaft.
3.1.2. Place grinding disc on the spindle.
3.1.3. retain disc with nut flange. Fit with spigot facing out if disc is less than 5mm thick, and facing in if disc is more than 5mm thick ( fig.2 & 3).
3.1.4. stop the spindle from turning by pushing in and holding the locking button (fig.4).
3.1.5. Lock the grinding disc into place by tightening the nut flange ( fig.5.10) with the disc spanner (fig.5.11).
3.1.6. release the locking button and check that it has sprung back to the initial position.
3.2. Positioning the Guard
the guard may be rotated through any angle to suit the task.
3.2.1. Position the guard to give working access whilst still providing maximum protection for the operator.
3.2.2. Lock the guard in place by tightening locking bolt ( fig.4).
3.3. Handle
the auxiliary handle will allow better control and safety.
3.3.1. Fit the handle by screwing it into the threaded hole on either
the left or right side of the gear box, as best suits the work.
3. ASSEMBLY
Model No. S0530 S0685
Power Input. . . . . . . . . . . . . .230V-2.6A. . . . . . . . . 230V-3.8A
Power . . . . . . . . . . . . . . . . . .600W . . . . . . . . . . . . . . . .860W
no Load speed . . . . . . . . . . .11000rpm . . . . . . . . . 11000rpm
maximum grinding disc size .115mm . . . . . . . . . . . . . 115mm
spindle thread. . . . . . . . . . . .m14 . . . . . . . . . . . . . . . . . . m14
Weight . . . . . . . . . . . . . . . . .2.1kg . . . . . . . . . . . . . . . . 2.3kg
Disc bore. . . . . . . . . . . . . . . .22mm . . . . . . . . . . . . . . . 22mm
sound pressure level . . . . . .89.3dB(A) . . . . . . . . . 89.5dB(A)
sound power level. . . . . . . . .102.3dB(A) . . . . . . . 102.5dB(A)
Vibration . . . . . . . . . . . . . . . .2.5m/s2 . . . . . . . . . . . . 2.4m/s2
CONTENTS LIST
1. . . . . . . . . . . . . . . . . . . . . . .Angle grinder
2. . . . . . . . . . . . . . . . . . . . . . . safety guard
3. . . . . . . . . . . . . . . . . . . . . . . . Disc flange
4. . . . . . . . . . . . . . . . . . . . . . . . . nut flange
5. . . . . . . . . . . . . . . . . . . . .Auxiliary handle
6. . . . . . . . . . . . . . . . . . . . . . .Disc spanner
2. CONTENT & SPECIFICATION
 WARNING! This tool is not intended for continuous professional use.
remove items from packing and identify parts against fig.1. check to ensure they are in good condition. If any part is damaged or missing
contact your supplier immediately.
Risk of Hand Arm Vibration Injury
Angle Grinder models: s0530, s0685 when operated in accordance with these instructions and tested in accordance with En 28662-4:1988 result in the following
vibration emissions declared in accordance with Bs En Iso 8662-4:1995, Iso 8662-4:1994
measured vibration emission value: s0530: 2.5m/s², s0685: 2.4m/s²
uncertainty: s0530: 1.0m/s², s0685: 1.0m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test. This tool may cause hand-arm
vibration syndrome if its use is inadequately managed. Recommended Measures to reduce risk of hand-arm vibration syndrome:
this item represents a low Hand Arm Vibration risk to users. the calculated maximum usage period exceeds 8 hours. We recommend appropriate safety
equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury.
DANGER OF FIRE/ExPLOSION HAzARD
 WARNING! The grinding process can produce streams of sparks which are a potential source of ignition, especially when grinding metal.
 DO NOT use the grinder where there are flammable liquids, solids or gases.
 DO NOT allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. Fabrics contaminated with
flammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.

To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in preference to
man-made fibres.
fig.2
fig.3
fig.5
fig.1
fig.4
Original Language Version s0530.V2, s0685.V2 Issue: 2 - 16/02/10