beautypg.com

Sealey TC180 User Manual

Tile cutter, Tc180.v2, Instructions for

background image

InstructIons for:

TILE CUTTER

MoDEL no:

TC180.V2

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND

CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY

CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.2

GENERAL SAFETY

familiarise yourself with the application, limitations and potential hazards of the tile cutter.

WARNING! Disconnect the cutter from the mains power before changing accessories, servicing or performing any maintenance.

the machine must only be serviced by a qualified person or service agent. contact your sealey dealer for information.

Place the cutter on a supporting surface strong enough to take the weight of the machine and workpiece during operation.

Keep the work area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.

Inhaling dust can be harmful - always wear respiratory protection and ensure that there is adequate ventilation.

Maintain the

cutter in good condition, check moving parts alignment regularly. Keep blade clean and in good condition.

replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

WARNING! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.

A guard, or any other part, that is damaged must be repaired or replaced before the tool is next used. the safety guard is a mandatory

fitting when the cutter is used on premises covered by the Health & safety at Work Act.

Before commencing work, ensure the blade is mounted correctly, securely fastened and is compatible with the machine, spindle speed and the

material to be cut. never use a blade which is damaged, bent or warped. use only recommended blades.

remove adjusting keys and wrenches from the machine and the vicinity before turning it on.

Machine operators must have received sufficient training and instructions as to the dangers posed by the cutter and the precautions to be observed.

operators must be under the supervision of a person who has a thorough knowledge and experience of the machine and the required guards.

WARNING! Wear approved safety eye protection, ear defenders and respiratory protection.

remove ill-fitting clothing. remove ties, watches, rings and other loose jewellery and contain long hair.

1.1.

ELECTRICAL SAFETY

WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A

residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current

Device (rcD) is used. It is particularly important to use an rcD with portable products that are plugged into a supply which is not protected

by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current Device by contacting your sealey dealer.

You must also read and understand the following instructions concerning electrical safety.

1.1.1. the

Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance tester (PAt), at least once a year.

1.1.2. the

Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances

and the safety of the appliance operators.

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.

and use a Portable Appliance tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all

connections to ensure that none is loose.

1.1.6.

Important: Ensure that the voltage marked on the appliance matches the power supply

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7.

DO NOT pull or carry the appliance by the power cable.

1.1.8.

DO NOT pull the plug from the socket by the cable.

1.1.9.

DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty

item repaired or replaced by a qualified electrician. When an AstA/Bs approved uK

3 pin plug is damaged, cut the cable just above the plug and

dispose of the plug safely.

fit a new plug according to the following instructions (uK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer

insulation extends beyond the cable restraint and that the restraint is tight.

Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.

to rewire, connect the wires as indicated above -

DO NOT connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure

that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket

with your electrician.

1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcD fitted is preferred since any appliance

plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the

capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use

of 2.5mm² section cable.

1. SAFETY INSTRUCTIONS

FUSE RATING 5 AMP

Blue

Neutral

Wire

Yellow & Green

Earth Wire

Cable

Restraint

Brown

Live

Wire

Original Language Version

tc180.V2 Issue: 2 - 24/11/09