beautypg.com

Sealey AB9001 User Manual

Page 3

background image

pressure left in the hose. Disconnect the air brush from the

compressor.

4.11. During and immediately after operation, the finned pump head

may be hot and should not be touched. If the unit must be

moved, lift it by the handle only. Allow the unit to cool before

storing it.

4.12. Should there appear to be any loss of efficiency when

spraying, ensure first that the air brush is scrupulously clean

and functioning properly. If the air brush is satisfactory then

refer to the trouble shooting guide for the compressor.

FAULT

CAUSE

REMEDY

Low air flow.

Air valve plate or air valve is

Change the defective air valve plate

damaged.

or air valve.

Diaphragm damaged.

Change diaphragm.

The head screws are too loose.

Tighten the screws equally.

Air hose leaking.

Check seals or renew hose.

noisy operation.

The head screws are too tight.

Loosen the screws and then tighten

them equally. Do not overtighten.

Bearing fault.

Contact authorised service agent.

Humming noise but does

The head screws are too tight.

Loosen the screws and then tighten

not work.

them equally. Do not overtighten.

Armature fault.

Contact authorised service agent.

The compressor does not stop

Irregular functioning of compressor

Switch off compressor and contact

and the safety valve is tripped.

or broken pressure switch.

authorised service agent.

Before carrying out any maintenance, switch compressor off,

unplug it from the mains electricity supply, depressurise the

tank and allow unit to fully cool down.

WARNING! Never drain or attempt to remove the filter

bowl if the compressor is pressurised.

5.1. Keep the compressor clean and free of dust. DO NOT use

cleaning agents. Wipe the compressor using a slightly

dampened cloth and blow it over with compressed air if

available.

5.2. Ensure that the ventilation openings are clear. Do not allow

any extraneous material to enter the unit via any of the

ventilation openings.

5.3. Routinely drain any moisture from the regulator filter bowl by

carefully pressing the spring loaded valve at the bottom of the

bowl. Periodically remove the filter bowl and clean in a mild

detergent solution.

DO NOT use solvents, thinners or alcohol

to clean the filter bowl.

5.4. To prevent corrosion to the tank interior, drain it on a regular

basis by opening the drainage tap at the bottom of the tank to

release any moisture that may have accumulated. After

draining ensure the drainage tap is fully closed.

5.5. The troubleshooting guide below is intended to give you an

indication of what type of fault may have developed with your

compressor over a long period of service. The chart is not

intended as a guide on how to repair the fault yourself. In all

cases we recommend that the compressor be returned to an

authorised service agent for rectification.

5. MAINTENANCE & TROUBLESHOOTING

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk,

email [email protected] or phone 01284 757500.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: no liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park

,

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

email

Original Language Version

AB9001 Issue: 1 - 14/07/11

This manual is related to the following products: