Sealey SA800 - Manual (Page 2)

Model: . . . . . . . . . . .SA800.V5 . .SA801.V5
Pad size Ø (mm): . . . . . . . 150 . . . . . . . 150
Thread (UNF): . . . . . . . . . 5/16” . . . . . . 5/16”
Free Speed (rpm): . . . . . 10000 . . . . . 10000
Operating Pressure (psi): . . 90 . . . . . . . . 90
Air Consumption (cfm): . . . . 16 . . . . . . . . 16
Orbital Size (mm): . . . . . . . . . 5 . . . . . . . . . 5
Air Inlet (BSP):. . . . . . . . . . 1/4” . . . . . . 1/4”
Model: . . . . . . . . . . .SA800.V5 . .SA801.V5
Vacuum Outlet Ø (mm):. . . N/A . . . . . . . . 28
Complete with Velcro Pad: Yes . . . . . . . Yes
Noise Power (dB(A)): . . 100.3 . . . . . 100.3
Noise Pressure (dB(A)): . 89.3 . . . . . . 89.3
Weight (kg): . . . . . . . . . . . . 0.7 . . . . . . . 0.7
Vibration figure (m/s²): . . . 5.24 . . . . . . 5.24
Uncertainty figure (m/s²): . 1.01 . . . . . . 1.01
3.1. Air Supply: (Recommended hook-up is shown in fig.1)
3.1.1. Ensure the air valve (or throttle) is in the "off" position before connecting to the air supply.
3.1.2. You will require an air pressure and an air flow (cfm) according to the specification listed above.
3.1.3.  WARNING! Ensure the air supply is clean and does not exceed the pressure quoted while
operating the sander. Too high an air pressure and/or unclean air will shorten the sander’s life
due to excessive wear and may be dangerous causing damage and/or personal injury.
3.1.4. Drain the compressor air tank daily. Water in the air line will damage the sander.
3.1.5. Clean air inlet filter weekly.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8
metres). The minimum hose diameter should be 1/4” I.D. and fittings must have the same bore.
3.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain
that all connections are secure.
3.2. Couplings: Vibration may cause failure if a quick fit coupling is connected directly to the air
tool. To overcome this, connect a leader hose to the tool. A quick fit coupling may then be
used to connect the leader hose to the air line recoil hose. See figs.1 & 2.
Polycarbonate outer housing with soft rubber handgrip reduces hand chill and vibration with an overall
weight of 0.7kg. Features adjustable air regulator for additional control and exhaust muffler to reduce
noise emission. Supplied with Ø150mm hook-and-loop dust-free pad.
SA801.V5 has dust-free outlet for use with centralised dust extraction systems.
LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Contact with the toxic dust from the removal of
such paint must therefore be avoided. The following action must be taken before using the sander on a
surface that you suspect may contain lead paint.
1. User must determine potential hazard relating to age of paint to be removed (modern paints do
not have lead content).
2. DANGER! Keep all persons and pets away from the work area. The following are particularly
vulnerable to the effects of lead paint dust: Pregnant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Our ref SSP1699)
b) PE Coated Hooded Coverall (Our ref SSP267). c) Latex Gloves (Our ref SSP24).
4. Take adequate measures to contain the paint dust, flakes and scrapings.
5. Continue to wear safety equipment (3) and thoroughly clean all areas when task is complete.
6. Seal paint waste in bags or containers for disposal according to local regulations.
fig.2
fig.1
Original Language Version
SA800.V5, SA801.V5 Issue: 1 - 23/07/13
© Jack Sealey Limited
3. PREPARING SANDER
2. TECHNICAL SPECIFICATIONS