Maintenance, Danger of fire/explosion hazard – Sealey SA650 User Manual
Page 3
WARNING! Disconnect tool from air supply before changing accessories, servicing or performing
maintenance. Replace or repair damaged parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
5.1.
If the air supply does not have an oiler, lubricate the air tool daily with a few drops of Sealey air tool oil
dripped into the air inlet to prolong its life.
5.2.
Clean the tool after use.
5.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose
connectors. To remedy check the air supply and follow instructions in chapter 3.
b) Grit or gum deposits in the tool may also reduce performance. If your model has an air strainer
(located in the area of the air inlet), remove the strainer and clean it. Flush the tool out with gum
solvent oil or an equal mixture of SAE No 10 oil and paraffin. Allow to dry before use.
5.4.
For a full service contact your local Sealey service agent.
5.5.
When not in use, disconnect from air supply, clean tool and store in a safe, dry, childproof location.
5. MAINTENANCE
4.2. OPERATING.
WARNING! Ensure you have read, understood and apply safety instructions.
4.2.1. Connect the tool to the air supply.
4.2.2. To start the tool, hold firmly and slide the safety catch forward, whilst depressing the air control lever.
4.2.3. The disc must be running at its maximum speed before attempting to cut the workpiece.
4.2.4. Slowly and smoothly bring the cutting disc toward the workpiece (avoid jerky movements).
4.2.5. Exert adequate pressure on the tool to allow cutting according to the type and size of the material you
are working with.
4.2.6. Avoid subjecting disc to excessive strain, always hold tool firmly and ease disc against workpiece
(a harsh impact may break the disc). Maintain a controlled progression.
DO NOT allow tool to free run for an extended period of time as this will shorten its life.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Danger of Fire/Explosion Hazard
WARNING! The grinding process can produce streams of sparks (especially when grinding metal), which
are a potential source of ignition.
DO NOT use the grinder where there are flammable liquids, solids or gases.
DO NOT allow grinder sparks to make contact with the operator’s clothing or any other fabric such as
cleaning rags. Fabrics contaminated with inflammable materials such as petrol, oil, grease, paint and
solvents are a particular fire hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated
with a fire retardant in preference to man-made fibres.
Original Language Version
SA650.V3 Issue: 3(SP) - 20/11/13
© Jack Sealey Limited
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories
and packaging should be sorted, taken to a recycle centre and disposed of in a manner
which is compatible with the environment.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [email protected] or phone 01284 757500.