Installation / start-up / operation, Start-up, Operation – Miomare Sink Mixer Tap / Kitchen Mixer Tap / Bath and Shower Mixer Tap User Manual
Page 32
32 GB
Installation / Start-up / Operation
Position the fitting body
1
with the fitting base
seal
2
inserted into the opening of your
washbasin.
First place the C-sealing washer
6
under the
washbasin, then the C metal washer
7
onto
the threaded bolt
8
.
Now attatch the fastening nut
9
to the
threaded bolt
8
and tighten with an open-
ended spanner SW 12 mm until the fitting
1
is
seated firmly on the washbasin.
Unscrew the upper pop-up flange
15
from the
lower pop-up flange
17
.
From the top insert the upper pop-up flange
15
with the upper pop-up seal
14
into the wash-
basin drain hole.
Place the lower pop-up flange
17
with the
lower pop-up seal
16
beneath the washbasin
drain hole.
Now screw the lower pop-up flange
17
with
the upper pop-up flange
15
, so the pop-up
plastic nut
19
faces to the back.
Unscrew the pop-up plastic nut
19
from the
lower pop-up flange
17
, leaving the gasket
inside the threaded shaft of the lower pop-up
flange
17
.
ATTENTION! DANGER OF INJURY, SHEET
METAL HAS SHARP EDGES.
Temporarily remove the clip and pop-up joint
11
from the pop-up pivot rod
12
for installation.
Please be sure the seal reimains on the pop-up
pivot rod
12
.
Place the pop-up plastic nut
19
over the longer
piece of the pop-up pivot rod
12
. Be sure the
seal is placed between the ball and pop-up
plastic nut
19
.
Inset the short section of the pop-up pivot
rod
12
into the female thread of the lower
pop-up flange
17
and retighten the pop-up
plastic nut
19
hand tight.
Reattach the clip and pop-up joint
11
to the
pop-up pivot rod
12
.
Insert the pup-up pull rod
5
through the plas-
tic section of the pop-up joint
11
and tighten
the screw using a cross-tip screwdriver.
Connect the pop-up pull rod
5
with the pop-
up pull rod
3
using the screw joint
4
.
Verify the pop-up is working properly. The plas-
tic screw below the pop-up drain plug
13
may
need to be adjusted. Then retighten with the
lock nut.
Install the siphon by screwing the siphon and
the pop-up screw thread
18
.
Check the seals inside the swivel nuts
20
on
the flexible connection hoses
10
.
Screw the flexible connection hoses
10
to the
angle valves. Be sure to correctly install the
flexible connection hoses
10
to the cold-/hot
water hoses – left flexible connection hose
10
to the hot water connection, left angle valve,
and the right flexible connection hose
10
to
the cold water connection, right angle valve.
Start-up
After the initial commissioning, carefully check all
connections for leaks.
To remove any possible impurities the tap must be
flushed before being used for the first time. To do
this, proceed as follows:
Unscrew the aerator
29
from the fitting
1
.
Open the main water supply and allow the
water to flow for two minutes to flush out any
residues.
Then reattach the aerator
29
to the fitting
1
.
Operation
Note: If the tap has not been used for a long pe-
riod, flush the pipes thoroughly to avoid stagnation
and build-up of residue.
Open the main water supply.
Lift the handle
22
and swing it to the right or
left in order to regulate the speed or tempera-
ture of the water.
Hot water:
Swing the handle
22
to the left.