Yaskawa GPD506/P5 to P7 - Manual (Page 45)

Appendix 3- Parameter Cross Reference
Page 45 of 48
GPD506/P5 Parameter P7 Parameter
Param
No.
Nxxx
Parameter
Name
Description or Selection Description or Selection
Parameter
Name
Param.
No.
100 Time of average
KW Set unit:1 (1=25ms)
Set range: 1-200 (25ms=5.0sec) 0 to 2000
Used to fine-tune the energy savings
function when in V/F control method. Power Detection Filter Time b8-05
101 MEMOBUS timeout
detection 0: Timeout detection disabled.
1: Timeout detection enabled. Enables or disables the communications
timeout fault (CE).
0: Disabled - A communication loss will
not cause a communication fault.
1: Enabled - If communication is lost for
more than 2 seconds, a CE fault will
occur. Communication Error
Detection
Selection H5-05
102 MEMOBUS Stop
method selection at
communication error (CE) 0: Deceleration stop
(Decelerate by deceleration time 1)
1: Coast stop
2: Deceleration stop
(Decelerate by deceleration time 2)
3: Continue operation (alarm display) Selects the stopping method when a
communication timeout fault (CE) is
detected.
0: Ramp to Stop
1: Coast to Stop
2: Fast-Stop
3: Alarm Only
4: Run at d1-04 Stopping Method after
Communication Error H5-04
104 MEMOBUS
Slave address Set unit:1 Set range:0-31
(There is no MEMOBUS communication at
set point =0) 0 to 20 Hex
Selects Drive station node number
(address) for Modbus terminals R+, R-, S+,
S-. The Drive’s power must be cycled for
the setting to take effect. Drive Node Address H5-01
105 MEMOBUS
Baud rate selection 0: 2400bps
1: 4800bps
2: 9600bps Selects the baud rate for Modbus terminals
R+, R-, S+ and S-. The Drive’s power must
be cycled for the setting to take effect.
0: 1200 bps
1: 2400 bps
2: 4800 bps
3: 9600 bps
4: 19200 bps
Communication Speed
Selection H5-02
106 MEMOBUS
Parity selection 0: Parity none
1: Even parity
2: Odd parity Selects the communication parity for
Modbus terminals R+, R-, S+ and S-. The
Drive’s power must be cycled for the
setting to take effect.
0: No Parity
1: Even Parity
2: Odd Parity Communication Parity
Selection H5-03
108 Motor no-load current Set unit: 1%
Set range: 0-99%
(100%= rated current of motor) Set to the magnetizing current of the motor
as a percentage of full load amps (E2-01).
This value is automatically set during
rotational Auto-Tuning. No-Load Current E2-03
110 Operator Connection Fault
Detect Select 0: Operator connection fault disabled.
1: Operator connection fault enabled. Determines if the Drive will stop when the
Digital Operator is removed when in
LOCAL mode or b1-02=0.
0: Disabled - The Drive will not stop when
the Digital Operator is removed.
1: Enabled - The Drive will fault (OPR)
and coast to stop when the operator is
removed. Operation Selection when
Digital
Operator is Disconnected o2-06
111 Local/remote Change- over
function Select 0: Cycle External run
1: Accept external run 0: Cycle External RUN - If the run
command is closed when switching from
local mode to remote mode, the Drive
will not run.
1: Accept External RUN - If the run
command is closed when switching
from local mode to remote mode, the
Drive will run. Local/Remote Run Selection b1-07
112 Low frequency OL
starting point Set unit: 0.1Hz
Set range: 0.0-10.0Hz
113 Continuous running
level at 0Hz Set unit: 1%
Set range: 25-100%
This parameter assists in protecting the
output transistors from overheating when
output current is high and output frequency
is low (6Hz and less).
0: Disabled
1: Enabled (L8-18 is active)
OL2 Characteristic Selection
at
Low Speeds L8-15