Yaskawa GPD506/P5 to P7 - Manual (Page 43)

Appendix 3- Parameter Cross Reference
Page 43 of 48
GPD506/P5 Parameter P7 Parameter
Param
No.
Nxxx
Parameter
Name
Description or Selection Description or Selection
Parameter
Name
Param.
No.
075 Set frequency
detection level Set unit: 0.1Hz and set range: 0.0-400.0Hz 0.0 to 200.0
L4-01 and L4-02 are used in conjunction
with the
multi-function outputs, (H2-01and H2-02)
as a setpoint
and hysteresis for a contact closure. Speed Agreement Detection
Level L4-01
076 Width of frequency
agreement detection Set unit: 0.1Hz and set range: 0.0-25.5Hz 0.0 to 20.0
Speed Agreement Detection
Width L4-02
077 Overtorque/
Undertorque
Selection 0: Overtorque/undertorque detection disabled.
1: Overtorque is detected during constant
speed operation and operation continues
after overtorque detection.
2: Overtorque is always detected and
operation continues after overtorque
detection.
3: Overtorque is detected during constant
speed operation and inverter output is
disabled after overtorque detection.
4: Overtorque is always detected and inverter
output is disabled after overtorque detection.
5: Undertorque is detected during constant
speed operation and operation continues
after undertorque detection.
6: Undertorque is always detected and
operation continues after undertorque
detection.
7: Undertorque is detected during constant
speed operation and inverter output is
disabled after undertorque detection.
8: Undertorque is always detected and inverter
output is disabled after undertorque
detection.
Determines the drive's response to an
overtorque /
undertorque condition. Overtorque and
Undertorque
are determined by the settings in
parameters L6-02 and
L6-03.
0: Disabled
1: OL@SpdAgree - Alm (Overtorque
Detection only
active during Speed Agree and Operation
continues
after detection)
2: OL At RUN - Alm (Overtorque
Detection is always
active and operation continues after
detection)
3: OL@SpdAgree - Flt (Overtorque
Detection only
active during Speed Agree and drive output
will shut
down on an OL3 fault.)
4: OL At RUN - Flt (Overtorque Detection
is always
active and drive output will shut down on
an OL3
fault.)
5: UL@SpdAgree - Alm (Undertorque
Detection is
only active during Speed Agree and
operation
continues after detection.)
6: UL at RUN - Alm (Undertorque
Detection is always
active and operation continues after
detection.)
7: UL @ SpdAgree - Flt (Undertorque
Detection only
active during Speed Agree and drive output
will shut
down on an OL3 fault.)
8: UL At RUN - Flt (Undertorque
Detection is always
active and drive output will shut down on
an OL3
fault.) Torque Detection Selection 1
L6-01
078 Overtorque detection
level Set unit: 1%
Set range: 30-200%
(100%= rated current of inverter) 0 to 300
Sets the overtorque/undertorque detection
level as a
percentage of Drive rated current. Torque Detection Level 1 L6-02
079 Overtorque detection time Set unit: 0.1sec and set range: 0.1-10.0sec 0.0 to 10.0
Sets the length of time an Over/Under
torque condition must exist before torque
detection 1 recognized by the Drive. Torque Detection Time 1 L6-03
080 (timer function)
ON Delay time Set unit: 0.1sec
Set range: 0.0-25.5sec 0.0 to 3000.0
Used in conjunction with a multi-function
digital input and a multi-function digital
output programmed for the timer function.
This sets the amount of time between when
the digital input is closed, and the digital
output is energized. Timer Function ON-Delay
Time b4-01