Verilink IMUX (880-503137-001) Product Manual - Manual (Page 29)

Configuration Menus
Verilink IMUX User Manual 3-3
Figure 3-2 IMUX Configuration Menu Options
Table 3-2 describes the IMUX Configuration Menu options and
Table 3-3 describes the status fields. The IMUX Configuration
Menu customizes to reflect the DIM attached to the back. The back
cards available are the HSSI (DIM 3664) and V.35 (DIM 3634).
Table 3-2 IMUX Configuration Menu
-- IMUX CONFIGURATION MENU -- -- IMUX CONFIGURATION MENU -- -- IMUX CONFIGURATION MENU -- -- IMUX CONFIGURATION MENU --
FW Rev : 2.10 FW Rev : 2.10 FW Rev : 2.10 FW Rev : 2.10
Line Type : T1 DSR) yes
Line Type : T1 DSR) yes Line Type : T1 DSR) yes Line Type : T1 DSR) yes
Channel Rate : 64K CTS) no
Channel Rate : 64K CTS) no Channel Rate : 64K CTS) no Channel Rate : 64K CTS) no
R) Rx Clk Phase: NORMAL DCD) yes
R) Rx Clk Phase: NORMAL DCD) yes R) Rx Clk Phase: NORMAL DCD) yes R) Rx Clk Phase: NORMAL DCD) yes
T) Tx Clk Phase: INVERT RI) yes
T) Tx Clk Phase: INVERT RI) yes T) Tx Clk Phase: INVERT RI) yes T) Tx Clk Phase: INVERT RI) yes
F) Ref Clk Phase: NORMAL TM) no
F) Ref Clk Phase: NORMAL TM) no F) Ref Clk Phase: NORMAL TM) no F) Ref Clk Phase: NORMAL TM) no
H) DTE Handshake: AUTOMATIC
H) DTE Handshake: AUTOMATIC H) DTE Handshake: AUTOMATIC H) DTE Handshake: AUTOMATIC
DTE Type: V.35
DTE Type: V.35 DTE Type: V.35 DTE Type: V.35
Backplane Bus: D:A Backplane Bus: D:A Backplane Bus: D:A Backplane Bus: D:A
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Lines Equipped: X X
Lines Equipped: X X Lines Equipped: X X Lines Equipped: X X
Lines Active: X X
Lines Active: X X Lines Active: X X Lines Active: X X
Frame Sync: X X
Frame Sync: X X Frame Sync: X X Frame Sync: X X
CTS Received: X X
CTS Received: X X CTS Received: X X CTS Received: X X
CRC Error:
CRC Error: CRC Error: CRC Error:
Far CRC Error:
Far CRC Error: Far CRC Error: Far CRC Error:
X) main menu X) main menu X) main menu X) main menu
A [0.0.0.2] [1,5] IMUX > A [0.0.0.2] [1,5] IMUX > A [0.0.0.2] [1,5] IMUX > A [0.0.0.2] [1,5] IMUX >
Command V.35 HSSI Description Options
R X Rx Clk Phase—Receive clock phase. Most configurations require
normal.
1) Normal
2) Inverted
T X X Tx Clk Phase—Transmit clock phase. Most configurations require
inverted.
1) Normal
2) Inverted
F X X Ref Clk Phase—Reference clock phase. Most configurations
require normal.
1) Normal
2) Inverted
H X DTE Handshake—Selects the control lead mode. If manual mode
is selected, each control lead must be forced “On” or it will be
forced “Off”. If manual mode is selected, DSR must be forced “On”
or no user data is sent (never send data option).
In Automatic DTE handshake mode, each lead is asserted
according to the state of the complimentary lead. In automatic
mode, DSR is output high and user data is sent if the DTE asserts
DTR. In this mode, leads may not be forced “On” or “Off”.
1) Automatic
2) Manual