Verilink IMUX (880-503137-001) Product Manual - Manual (Page 22)

Quick Set-Up
2-8 Verilink IMUX User Manual
2. Use the M command to set the mode to 64k (option 1), this
means that each DS0 timeslot used will use the full 64 kbit/s
of bandwidth.
3. Type "SP" to set the source port, type "1,7" then type "1" to
select Net 1.
4. Use the SM command to set the DS0 mapping to all 24 by
typing "SM" and entering "1-24" at the prompt.
5. Use the DP command to set the destination port to shelf 1, slot
8—the IMUX module (1,8). Since there is only one port on an
IMUX module, no further entry is required for the destination.
The screen indicates that the data rate for port 1 is now 1.528
Mbit/s.
NOTE: When the Setup command is used, the SCM selects the
midplane bus for this circuit.
The setting for mode is already correct. Type “S” to set up the
circuit. A message should appear Successful Circuit Build. Exit
to the Circuit Manager Menu with the X command. The menu
should list both circuits as active (
Figure 2-6 ).
Figure 2-6 Circuit Manager Menu with Circuit
Cloning a Circuit With at least one circuit in the SCM database, additional circuits can
be created by cloning an existing circuit.
-- CIRCUIT MANAGER MENU [1,1] SCM Firmware 2.05 -- -- CIRCUIT MANAGER MENU [1,1] SCM Firmware 2.05 -- -- CIRCUIT MANAGER MENU [1,1] SCM Firmware 2.05 -- -- CIRCUIT MANAGER MENU [1,1] SCM Firmware 2.05 --
Page : 1 Page : 1 Page : 1 Page : 1
Total: 1 circuits
Total: 1 circuits Total: 1 circuits Total: 1 circuits
Name Type Mode Prio Source Port Dest Port Bus Status Name Type Mode Prio Source Port Dest Port Bus Status Name Type Mode Prio Source Port Dest Port Bus Status Name Type Mode Prio Source Port Dest Port Bus Status
------------ ---- ---- ---- ---------------- ---------------- --- ------
------------ ---- ---- ---- ---------------- ---------------- --- ------ ------------ ---- ---- ---- ---------------- ---------------- --- ------ ------------ ---- ---- ---- ---------------- ---------------- --- ------
QUADT1_IMUX1 perm 64k norm [1, 7] QUAD net1 [1, 8] IMUX data AUT Active
QUADT1_IMUX1 perm 64k norm [1, 7] QUAD net1 [1, 8] IMUX data AUT Active QUADT1_IMUX1 perm 64k norm [1, 7] QUAD net1 [1, 8] IMUX data AUT Active QUADT1_IMUX1 perm 64k norm [1, 7] QUAD net1 [1, 8] IMUX data AUT Active
A) add circuit L) search circuit A) add circuit L) search circuit A) add circuit L) search circuit A) add circuit L) search circuit
D) delete circuit E) edit circuit
D) delete circuit E) edit circuit D) delete circuit E) edit circuit D) delete circuit E) edit circuit
P) prev page I) activate circuit P) prev page I) activate circuit P) prev page I) activate circuit P) prev page I) activate circuit
N) next page R) deactivate circuit
N) next page R) deactivate circuit N) next page R) deactivate circuit N) next page R) deactivate circuit
X) exit this menu X) exit this menu X) exit this menu X) exit this menu
A [0.0.0.2] [1,8] IMUX > A [0.0.0.2] [1,8] IMUX > A [0.0.0.2] [1,8] IMUX > A [0.0.0.2] [1,8] IMUX >