Skutch Electronics AS-101 - Manual (Page 9)

Al Sandige Page 9 12/05/01
To change, enter 1, then enter the new number
of Re-dials you want, then enter #. You can enter 00
through 99. Default is 02.
To leave unchanged, enter #.
5) Reset Char. This is the touch tone digit you need
to enter 2 times in order to reset the AS-101 over
the phone.
To change, enter 1, then enter the new digit you
want to use as the reset character, then enter #. You
can enter 0 through 9 or *. Default is *.
To leave unchanged, enter #.
6) Trigger Tone. This is the touch tone digit the
AS-101 looks for as the alert in modes 1 and 2,
and the tone for Group 1 in mode 6.
To change, enter 1, then enter the new digit you
want to use as the trigger tone, then enter #. You can
enter 0 through 9 or *. Default is 8.
To leave unchanged, enter #.
7) Trigger Tone 2. This is the touch tone digit the
AS-101 looks for as the alert tone for Group 2 in
mode 6.
To change, enter 1, then enter the new digit you
want to use as the trigger tone 2, then enter #. You
can enter 0 through 9 or *. Default is 5.
To leave unchanged, enter #.
8) Pager Char. This is the touch tone digit that the
AS-101 will use to fill your pager display in
simple pager mode.
To change, enter 1, then enter the new digit you
want to use as the pager character, then enter #. You
can enter 0 through 9 or *. Default is 5.
To leave unchanged, enter #.
9) Mode. This selects which of the 6 operating
modes to use.
To change, enter 1, then enter the number for
the new mode you want to use, then enter #. You can
enter:
1 for Tone Mode,
2 for Tone and Pulse Mode,
3 for Every Call Mode,
4 for Voice Control Mode,
5 for Specific Mode,
6 for Grouped Mode.
To leave unchanged, enter #.
10) Voice Trig .1. This is the amount of voice the
AS-101 needs to see, in .1 second units, to
trigger in Voice Control Mode.
To change, enter 1, then enter the new amount
of voice, then enter #. You can enter 01 through 99,
which is .1 seconds through 9.9 seconds. Default is
20, or 2.0 seconds.
To leave unchanged, enter #.
11) Voice Win Sec. This is the amount of time you
want the AS-101 to look for the audio it needs in
Voice Control Mode. You should try to make
this value at least twice the Voice Trig .1 value.
To change, enter 1, then enter the new window
length in seconds, then enter #. You can enter 1
through 9, which is 1 seconds through 9 seconds.
Default is 4 seconds.
To leave unchanged, enter #.
12) Confirmation. This tells the AS-101 whether or
not to play a confirmation signal to the call when
the AS-101 gets triggered.
To change, enter 1, this is a toggle so you can
enter 1 to turn confirmation off, then you can enter 1
to turn confirmation back on. Default is off.
To leave unchanged, or to advance when
finished, enter #.
13) Alert Tone Len. This is the amount of time the
AS-101 will play the Alert Tone for voice calls.
To change, enter 1, then enter the new length
for the Alert Tone, then enter #. You can enter 00
through 99, which is 0 seconds through 99 seconds.
Default is 20 seconds.
To leave unchanged, enter #.
System Counters
The AS-101 has two independent 4 digit
counters. The first counter is the TOTAL TRIGGER