Pacific Research Solutions RI-1 User Manual
Page 79
Pacific Research Solutions
RI-1 and PE-1 User Manual
Page 73
SECTION 19
SYSTEM COMMAND TABLE
S-Cmd
Command Description
and Data Format
Command
Syntax
Factory
Setting
Stored
Location
00 Signal
Polarity
Item 0 = NSQ, 1 = TSQ, 2 = PTT (0=Active Lo, 1=Active Hi)
Item 3 = RX Audio Type (0=Flat, 1=Emphasized)
00 [Item] [Mode]
All 0
RAM
EEPROM
01
Repeater Port Mode
Mode 0 = Off, 1 = NSQ only, 2 = TSQ Only, 3 = NSQ & TSQ,
Mode 4 = Open Squelch.
01 [Mode]
0, Off
RAM
EEPROM
02
RX Gain Adjust
Level 0-24 [-24db to +27db]
02 [Level]
12, 0db
RAM
EEPROM
03
Low Pass Filter Select
0 = 2500Hz, 1 = 3000Hz, 2 = 3500Hz, 3 = 4000Hz, 4 = 4500Hz
03 [Select]
2, 3500Hz
RAM
EEPROM
04
Repeater carrier delay time
Time = 0 to 255 in 1/10 second increments
04 [Time]
30,
3.0 Sec
RAM
EEPROM
05
Force on repeater PTT for set time
Time = 0 to 3600 second
05 [Time]
0 Sec.
Power
On
06
Suppress Function ACK one time
Mode 0 = Clear Suppress, 1 = Suppress function complete/error one time
06 [Mode]
0
RAM
07
ID interval time
Time = 0 to 255 in 6 seconds increments, 0 = disable
07 [Time]
10.0 Min.
RAM
EEPROM
08
Courtesy message timer, COS falling to start of message
Time = 0 to 99 in 1/10 second increments, 0 = disable
08 [Time]
1.5 Sec.
RAM
EEPROM
09 Reserved
10 Transmitter
time-out
Time = 0 to 255 in 6 seconds increments,
0 = disable, * = Reset timer
10 [Time]
0
0.0 Min.
RAM
EEPROM
11
Alternate command terminator
Terminate 0 = None (COS Only), 1-4 = A-D, 5 = *, 6 = #,
7 = Inter-digit timer, 8 = Min 1 digit cmds, 9 = Min 2 digit cmds, 10 = Min
3 digit cmds, 11 = Min 4 digit cmds, 12 = Min 5 digit cmds, 13 = Min 6
digit cmds, 14 = Min 7 digit cmds, 15 = Min 8 digit cmds
11 [Terminate]
7
Inter-digit
RAM
EEPROM
12 Reserved
13
User Command control NSQ/TSQ mode
Mode 0 = Off, 1 = NSQ, 2 = TSQ, 3 = NSQ & TSQ
14 [Mode]
1,
NSQ
RAM
EEPROM
14
System Command control NSQ/TSQ mode
Mode 0 = Off, 1 = NSQ, 2 = TSQ, 3 = NSQ & TSQ
14 [Mode]
1,
NSQ
RAM
EEPROM
15
User command group enable
Group = 0 to 1
Mode 0 = Disable (off), 1 = Enable (on)
15 [Group] [Mode]
0, On
1, Off
RAM
EEPROM
16
DTMF Decode Inter digit time
Time = 1 to 99 in 1/10 seconds increments
16 [Time]
35
3.5 Sec.
RAM
EEPROM
17
DTMF Decode Mute time
Time = 0 to 99 in 1/10 seconds increments, 0 = No mute
17 [Time]
25
2.5 Sec.
RAM
EEPROM
18 Reserved
19 Resend
DTMF
Digits = 0 to 9, *, # , A, B, C, D (15 digits max.)
19 [Digits]
N/A
N/A