Pacific Research Solutions RI-1 - Manual (Page 5)

Pacific Research Solutions RI-300 User Manual
Page iii
S-Cmd 16 DTMF INTER-DIGIT TIME........................................................................................................................34
S-Cmd 17 DTMF MUTE DELAY TIME......................................................................................................................34
S-Cmd 18 RESERVED..................................................................................................................................................35
S-Cmd 19 GENERATE DTMF OUT ............................................................................................................................35
S-Cmd 20 REMOTE BASE INTERFACE MODE .......................................................................................................35
S-Cmd 21 REMOTE BASE USER FUNCTIONS BITS...............................................................................................35
S-Cmd 22 REMOTE BASE USER FUNCTION BYTE ...............................................................................................35
S-Cmd 23 REMOTE BASE RADIO FUNCTIONS BITS ............................................................................................35
S-Cmd 24 REMOTE BASE FREQUENCY SET ..........................................................................................................36
S-Cmd 25 REMOTE BASE TSQ SELECT...................................................................................................................36
S-Cmd 26 REMOTE BASE TSQ MODE......................................................................................................................36
S-Cmd 27 REMOTE BASE TX POWER SELECT ......................................................................................................36
S-Cmd 28 REMOTE BASE SQUELCH ADJUST........................................................................................................36
S-Cmd 29 REMOTE BASE VOLUME CONTROL .....................................................................................................36
S-Cmd 30 REMOTE BASE CUSTOM FUNCTION SET ............................................................................................36
S-Cmd 31 TONE GENERATOR MESSAGE EDITOR................................................................................................37
Tone Generator Command Descriptions.......................................................................................................37
Default Tone Generator Messages ................................................................................................................37
Tone Generator Command List.....................................................................................................................38
Reset Tone Generator Command ..................................................................................................................38
S-Cmd 32 SET MESSAGE EVENTS ...........................................................................................................................39
S-Cmd 33 RESET MESSAGE.......................................................................................................................................39
S-Cmd 34 AUXILIARY OUTPUT MODE...................................................................................................................39
S-Cmd 35 AUXILIARY INPUT MODE.......................................................................................................................40
S-Cmd 36 AUXILIARY INPUT MUTE/MIX MODE.................................................................................................. 40
S-Cmd 37 REGENERATE FROM THE AUXILIARY INPUT....................................................................................40
S-Cmd 38 AUXILIARY GAIN ADJUST......................................................................................................................40
S-Cmd 39 CONTROLLER UNIT ADDRESS...............................................................................................................41
S-Cmd 40 DELAY TIMER EVENT .............................................................................................................................41
S-Cmd 41 RECEIVER INACTIVITY TIMER EVENT ...............................................................................................41
S-Cmd 42 REGULAR INTERVAL EVENT.................................................................................................................42
S-Cmd 43 RESERVED..................................................................................................................................................42
S-Cmd 44 RESERVED..................................................................................................................................................42
S-Cmd 45 PORT INPUT – STATE CHANGE EVENT ...............................................................................................43
S-Cmd 46 PORT OUTPUT ON / OFF ..........................................................................................................................43
S-Cmd 47 through 54 RESERVED ................................................................................................................................43
S-Cmd 55 PASSWORD FOR S-COMMAND ACCESS...............................................................................................43
S-Cmd 56 RESERVED..................................................................................................................................................43
S-Cmd 57 RESERVED..................................................................................................................................................43
S-Cmd 58 REMOTE SOFTWARE RESET ..................................................................................................................44
S-Cmd 59 REMOTE EEPROM INITIALIZE ...............................................................................................................44
S-Cmd 60 RESERVED..................................................................................................................................................44
S-Cmd 61 RESERVED..................................................................................................................................................44
S-Cmd 62 DEFINING USER COMMANDS ................................................................................................................45
S-Cmd 63 MACRO EDITOR, SET STARTING LINE NUMBER POINTER.............................................................47
S-Cmd 64 MACRO EDITOR, INSERT S-COMMANDS.............................................................................................47
S-Cmd 65 RESERVED..................................................................................................................................................48
S-Cmd 66 READ / WRITE SYSTEM DATA ...............................................................................................................48
S-Cmd 67 RESERVED..................................................................................................................................................48
S-Cmd 68 MACRO LINE JUMP...................................................................................................................................48
S-Cmd 69 EXIT S-COMMAND PROGRAMMING ....................................................................................................49
S-Cmd 70 through 99 RESERVED ................................................................................................................................49
SECTION 12 USER COMMANDS and MACROS..........................................................................50
DEFINITION of TERMS...................................................................................................................................................51
PROGRAMMING STANDARD USER COMMANDS and MACROS ...........................................................................52
Example of programming a standard user command and macro .................................................................................53
Example of programming macro data into the macro data memory:...........................................................................53
Passing S-Commands to Another Controller...............................................................................................................54
USER S-COMMANDS......................................................................................................................................................54