Denon AVR-4800 - Manual (Page 37)

37
System call function
• The included remote control unit is equipped with a system call function for transmitting multiple remote control signals when a single button
is pressed (this is often referred to as a “macro” function).
This function can be used to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on a source
component’s power and start playback, etc., all at the touch of a button.
(1) System call buttons
The buttons that can be used for the system call function are shown on the table below.
A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up to 5 operations can be performed
with other buttons.
System call signals are already preset at the buttons indicated in the shaded section. System call signals can also be stored at any button on
the remote control unit, including the buttons in this section. (See page 38.)
Button
POWER OFF
(key 3)
POWER ON
(key 4)
DVD (key 5)
VDP (key 6)
TV/DBS
(key 9)
V.AUX
(key 10)
VCR-1
(key 13)
CD (key 14)
No.
transmissions
10
10
5
5
5
5
5
5
Stored
operation 1
Receiver
power on
Receiver
power on
Receiver
power on
Receiver
power on
Receiver
power on
Receiver
power on
Stored
operation 2
DVD player
(DVD)
power on
LD player
(VDP)
power on
TV power on
TV power on
Video (VCR)
power on
Receiver
input source
switched to
CD
Stored
operation 3
Receiver
input source
switched to
DVD
Receiver
input source
switched to
VDP
Receiver
input source
switched to
TV/DBS
Receiver
input source
switched to
V.AUX
Receiver
input source
switched to
VCR-1
Stored
operation 4
TV power on
TV power on
TV power on
Stored
operation 5
DVD player
(DVD)
playback
LD player
(VDP)
playback
Video (VCR)
playback
Stored
operation 6
Stored
operation 7
Stored
operation 8
Stored
operation 9
Stored
operation 10
The system call signals for the POWER OFF and
POWER ON buttons are transmitted from the remote
control unit approximately once every second.
The signals for the other buttons (DVD, VDP, TV/DBS,
V.AUX, VCR-1 and CD) are transmitted approximately
once every 1.5 seconds.
(2) Using the system call function
1 Press the system call button.
• The LEARNED/TX LED flashes for 5 seconds.
CALL
2 Press the button at which the desired system call signals are
stored while the LEARNED/TX LED is flashing.
• The preset signals or the signals you have stored at that
button are transmitted in succession.
DVD
START LEARNED/TX
HOME THX CINEMA
TUNING
BAND TITLE MENU/GUIDE
MODE
DOLBY / DTS
SURROUND DIRECT
DSP SIMULATION 5CH / 7CH STEREO STEREO
INPUT MODE ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS V.AUX PHONO
VCR-1 CD MD / TAPE-1 CHANNEL
VCR-2 TAPE-2 MON TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MD
MULTI
DECK
SYSTEM SETUP SURROUND PARAMETER
CH SELECT
SELECT
RC-869
1 2 3
4
SET
A / B
CALL OFF
ENTER
ON / SOURCE
5 6
7 8 9
+10 0
2
1