Denon AVR-4800 - Manual (Page 18)

18
7 SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 6 to 15), make the
various settings described below on the monitor screen using the AVR-4800’s on-screen display function.
These settings are required to set up the listening room’s AV system centered around the AVR-4800.
• Use the following buttons to set up the system:
TUNING
BAND
TITLE MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE MULTI SPEAKER
RETURN
DVD
SET UP
STATUS
DISPLAY
ON SCREEN
MUTING
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MD
LOCK
DECK
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
ENTER
SYSTEM SETUP button
Press this to display the system setup menu.
SURROUND PARAMETER button
Press this to display the surround parameter menu.
ENTER button
Press this to switch the display on the screen.
Also use this button to complete the setting on the screen.
CURSOR buttons
and : Use these to move the cursors ( 0 and 1 ) to the left and right
on the screen.
and : Use these to move the cursors ( • and ª ) up and down on the
screen.
• System setup items and default values (set upon shipment from the factory)
System setup Default settings
q
w
t
y
u
i
o
Speaker
Configuration
(Surround
Speaker
Setting)
Subwoofer mode
THX
Surround EX
Channel
Level
Subwoofer
Peak Limit
Lev
Digital In
Assignment
On Screen
Display
Auto Tuner
Presets
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for full-
size, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
Use this function when using multiple surround speaker
combinations for more ideal surround sound. Once the
combinations of surround speakers to be used for the
different surround modes are preset, the surround
speakers are selected automatically according to the
surround mode.
This selects the subwoofer speaker for playing deep bass signals.
Select the operation when the “THX Surround EX” surround
parameter is set to “ON”.
This adjusts the volume of the signals output from the speakers and
subwoofer for the different channels in order to obtain optimum
effects.
This parameter is for detecting the maximum level of the low bass
signals output from the subwoofer channel in order to protect the
subwoofer from damage and prevent unpleasant distorted sounds
from being produced.
This assigns the digital input jacks for the different input
sources.
This sets whether or not to display the on-screen display that
appears on the monitor screen when the controls on the remote
control unit or main unit are operated (from MONITOR 1 outputs
only).
FM stations are received automatically and stored in the memory.
Surround
mode
Surround
speaker
Input
source
Digital
Inputs
Front Sp.
Small
Center Sp. Surround Sp. Sub Woofer
Small Small Yes
DOLBY/
DTS
SURROUND
THX
SURROUND
WIDE
SCREEN
5CH/7CH
STEREO
DSP
SIMULATION
EXT. IN — —
A A A A A A — —
LFE —THX—
Front L & R Center Surround L & R Sub Woofer
12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m) 12 ft (3.6 m)
Front L Front R Center
Surround
R
Surround
Back R
Subwoofer
0 dB 0 dB 0 dB 0 dB 0 dB 0 dB
Peak Limiter = OFF
CD DVD VDP TV/DBS VCR-1 VCR-2 V. AUX TAPE-1
COAXIAL
1
COAXIAL
2
COAXIAL
3
OPTICAL
1
OPTICAL
2
OPTICAL
3
OPTICAL
4
OPTICAL
5
On Screen Display = ON
A1 ~ A8
B1 ~B8
C1 ~C8
D1 ~D8
E1 ~E8
87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz
520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
Surround Back Sp.
Small / 2spkrs
THX Surround EX = ON
e Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position. SBL & SBR
10 ft (3.0 m)
r Power Amp
Assignment Set this when the power amplifier for the front channels is
switched for use with the surround back channel.
Front / Center / Surround
Surround
Back L
0 dB
Surround
L
0 dB