Kenton Pro-SOLO MkII - Manual (Page 18)

18
Address Function Range Notes ( see end )
01h
Receive chan 0 - 15 { 1 }
02h trig / retrig 0 - 1
03h note priority 0 - 2
04h pitchbend range 0 - 24
05h portamento cont # 253 - 0 - 119 { 3 }
06h portamento time / rate 0 - 127
07h portamento type 0 – 1 0=fixed rate / 1= fixed time
08h LFO to CV depth controller # 252 - 0 - 119 { 4 }
09h LFO to CV min val 0 - 127
0Ah LFO to CV max val 0 - 127
0Bh LFO to CV reset val 0 - 127
0Ch coarse tune / transpose 232 > 0 > 24 { 2 }
0Dh fine tune val 129 > 0 > 127 129>0 = -ve
0Eh scale val 129 > 0 > 127 129>0 = -ve
0Fh v/o or hzv or 1.2v select 0 - 2
10h gate select 0 - 7 5 modes used
14h
Aux1 Cont # 239 > 0 > 119 { 6 }
15h Aux1 min val 0 - 127
16h Aux1 max val 0 - 127
17h Aux1 reset val 0 - 127
18h Key scale to Aux 0 - 127
19h LFO to Aux1 cont # 252 - 0 - 119 { 4 }
1Ah LFO to Aux1 min val 0 - 127
1Bh LFO to Aux1 max val 0 - 127
1Ch LFO to Aux1 reset value 0 - 127
1Eh
Lfo speed 0 - 127
1Fh Lfo waveshape 0 - 8 { 7 }
20h Lfo MIDI sync 0 - 96 { 8 }
21h Lfo sync start point 0 - 255
22h Key-on resets LFO wave 0 - 1 { 10 }
28h
cont = start 0 - 1 { 11 }
29h clock divide 0 - 24 { 9 }
2Ah thru / sync 24 / aux 2+3 0 - 2 0=thru / 1= sy24 / 2= aux 2+3
2Bh Aux 2 controller # 251 > 0 > 119 { 6 }
2Ch Aux 2 controller # 251 > 0 > 119 { 6 }
2Dh Sysex Device Number 0 - 15 { 1 } & { 12 }
{ NOTES }
{ 1 } Data 0 - 15 corresponds to MIDI channels or device numbers 1 - 16
{ 2 } 232 = -24 semitones 0 = no transpose 24 = + 24 semitones - 25 to 231 are invalid
{ 3 } 253=pmt off 254=pmt on 255=prg chng & 0 - 119
{ 4 } 252=ignore 253=pitchbend 254=velocity 255=aftertouch & 0 - 119
{ 5 } 0= -64 64=0 127=+63
{ 6 } 251=trig 252=ignore 253=p.bend 254=vel 255=aft & 0 - 119
{ 7 } 0= triangle 1= saw up 2= saw down 3= 10% pulse etc. as display
{ 8 } 1 - 96 corresponds to sync divide 1 to 96 and 0 = off
{ 9 } 0 - 23 corresponds to arpeggio divide 1 to 24
{ 10 } 0=off 1=on
{ 11 } 0 = continue ignored 1 = continue=start
{ 12 } WARNING – any messages after this will need to use the new device number
All sysex addresses and data are range checked and out-of-range values
will either be ignored or adjusted to give a valid response.