Specifications, Appendix b, Ab c – Conair WSB User Manual
Page 104
One Conair Drive
●
Pittsburgh, PA 15202
●
412-312-6000
●
FAX 412-312-6227
●
www.conairnet.com
MODELS
GB1840
GB1860
Performance characteristics
Batch size lbs {g}
39.7 {18000}
39.7 {18000}
Maximum throughput lbs/hr {kg/hr}*
4114 {1870}
2566 {1166}
Bin Capacity - Main Ingredient ft
3
{liter}
6.7 {189.7}
3.8 {107.6}
Bin Capacity - Minor Capacity ft
3
{liter}
3.8 {107.6}
3.8 {107.6}
Maximum number of materials
8
10
Number of discharge valves
4
6
Number of additive feeders
up to 4
up to 4
Control software (# of components)
4 or 12
12
Dimensions inches {mm}
A - Height above mounting plate
93 {2362.2}
93 {2362.2}
B - Width†
56 {1421.4}
56 {1421.4}
C - Depth†
34 {863.6}
34 {863.6}
D - Controller height
11.25 {285.75}
11.25 {285.75}
E - Controller width
12.25 {311.15}
12.25 {311.15}
F - Controller depth
8.19 {208.03}
8.19 {208.03}
Weight lbs {kg}
Installed
730 {331}
730 {331}
Shipping
850 {385.5}
850 {385.5}
Voltage Running load amps‡
110V/1 phase/60hz (control)
0.3
0.3
220V/1 phase/60hz (mixer)
8.2
8.2
220V/1 phase/60hz (control)
0.2
0.2
220V/1 phase/60hz (mixer)
8.2
8.2
220V/1 phase/50hz (control)
0.2
0.2
220V/3 phase/50hz (mixer)
4.4
4.4
400V/3 phase/50hz (mixer)
2.2
2.2
Compressed air requirements
Discharge valves
80 psi @ 0.2 ft
3
/min {5.5 bars @ 0.09 liters/sec}
1/4 in. NPT fitting
Maximum loader sizes §
Number of 20 inch loaders
2
3
Number of 15 inch loaders
4
6
GRAVIMETRIC BATCH BLENDERS
AutoWeigh GB1840 and 1860 Models
MOUNTING INTERFACE
SPECIFICATION NOTES
* Maximum throughput rates are based on 35 lb/ft
3
pel-
letized material and using all dispense valves. Use of
feeders for minor ingredients will reduce this rate.
Refer to the selection guide for more specific through-
put information.
† Feeders will increase width dimensions. Please refer
to feeder specification.
‡ Each auger feeder requires an additional 1 amp @
120V or 0.5 amp @ 240V.
§ Maximum loader sizes may be used only when
the loader is adjacent to loaders of a smaller
diameter.
(4) 9/16 in. {14.3 mm}
diameter bolt holes
4 in. {101.6 mm}
diameter
through hole
8 in. {203.2 mm}
square bolt pattern
15 in. {381 mm}
14.5 in.
{368.3 mm}
16 in.
{406.4 mm}
20 in. {508 mm}
SPECIFICATIONS
TPS014/1199
IB04
A
B
C
FRONT VIEW
GB1840/GB1860
SIDE VIEW
GB1840
TOP VIEW GB1840
B
C
4
3
2
1
FEEDER LOCATIONS
A
B
C
D
8
7
4
3
2
1
C
B
TOP VIEW GB1860
C
SIDE VIEW
GB1860
E
D
F
CONTROL
FEEDER LOCATIONS
A
B
D
C
NOTE: Any one of the
feeders (A,B,C or D)
can be designated
position 5 or 6.
APPENDIX B