Juniper Systems A2 Ethernet Dock User Manual
Page 2
Maintenance and Environmental Issues
The ethernet dock is intended for indoor use only.
Temperatures should be between 0°C to 50°C. Avoid using the
dock in situations where water can enter the connector ports.
It is not sealed against water and must be kept dry, although it
sheds moisture that is on the handheld when it is placed into
the dock.
Do not touch the docking pins (spring loaded contacts) with
conductive items when power is applied to the dock.
Do not drop items on the dock that can damage the pins.
Keep debris off of the docking pins and the connectors to
maintain the best performance.
Battery Warnings
WARNING!
These warnings are for the lithium ion
rechargeable batteries in the handheld:
To reduce the risk of fire or burns, do not disassemble, crush,
puncture, short external contacts, or expose to fire.
Do not disassemble or open, crush, bend or deform, puncture,
or shred.
Do not modify or remanufacture, attempt to insert foreign
objects into the battery, immerse or expose to water or other
liquids, expose to fire, explosion or other hazard.
Only use the battery for the system for which it is specified
Only use the battery with a charging system that has been
qualified with the system per this standard.
Do not short circuit a battery or allow metallic conductive
objects to contact battery terminals.
Replace the battery only with another battery that has been
qualified with the system.
Use of an unqualified battery may present a risk of fire,
explosion, leakage or other hazard.
Promptly dispose of used batteries in accordance with local
regulations.
Battery usage by children should be supervised.
Avoid dropping the battery. If the battery is dropped,
especially on a hard surface, and the user suspects damage,
take it to a service center for inspection.
Improper battery use may result in a fire, explosion or other
hazard.
Wall Charger Warnings
WARNING!
To reduce the risk of personal injury, electrical
shock, fire or damage to the equipment:
Plug the wall charger into an electrical outlet that is easily
accessible at all times.
Disconnect power from the equipment by unplugging the wall
charger from the electrical outlet.
Do not place anything on the wall charger cord or any of the
other cables. Arrange them so that no one may accidentally
step on or trip over them.
Do not pull on a cord or cable. When unplugging the wall
charger from the electrical outlet, pull on the plug, not the
cord.
Use only wall chargers intended for the handheld. Using any
other external power source can damage your product and
void your warranty.
!!
!
Regulatory Information
United States (FCC)
This device complies with Part 15 of the FCC Rules. Operation
of this equipment is subject to the following two conditions:
1. The device may not cause harmful interference.
2. This device must accept any interference received, even if
the interference may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
CAUTION:
Only approved accessories may be used with
this equipment. In general, all cables must be high quality,
shielded, correctly terminated, and normally restricted to two
meters in length. Wall chargers approved for this product
employ special provisions to avoid radio interference and
should not be altered or substituted.
CAUTION:
Changes or modifications to the handheld or dock
that are not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
Industry Canada
This Class A digital apparatus complies with Canadian
ICES-003. Cet appareil numérique de la classe A est conforme
à la norme NMB-003 du Canada.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
CE Marking
Products bearing the CE marking comply with the
2004/108/EC (EMC Directive) issued by the
Commission of the European Community.
CE compliance of this device is valid only if powered with/
by a CE-marked wall charger provided by the manufacturer.
Compliance with these directives implies conformity to the
following standards:
EN 55022 Electromagnetic Interference
EN 55024 Electromagnetic Immunity
!
!
P/N 24532-00. Copyright August 2014 Juniper Systems, Inc. Archer 2
Rugged Handheld and Allegro 2 Rugged Handheld are trademarks of
Juniper Systems, Inc. Information is subject to change without notice.
tel: 435.753.1881
l
web:
1132 W. 1700 N. Logan, UT 84321