Interlogix NX-592E - Manual (Page 10)

10 NX-592E NetworX Cellular Module Installation Sheet
added the device to the controller key and system
network.
Note: To add a light module using the controller without adding
it to a specific number key on the controller, skip steps 4 and 5.
To add a thermostat to the system using the controller:
1. Press and hold the Setup button on the controller until the
screen displays “Light Setup”.
2. Use the arrow buttons to scroll until the screen displays
“Thermostat”. Press the OK button.
3. The screen should now display “Add”. Press the OK
button.
4. The screen should now display “Setup Waiting”. Follow
the device-specific directions for the thermostat you are
adding to the system to trigger it. The controller screen will
display “Success” to confirm you have successfully added
it to the system network.
To remove a light module from the system network using
the controller:
1. Press and hold the Setup button on the controller until the
screen displays “Light Setup”. Press the OK button.
2. The controller screen should now display “Add”. Use the
arrow buttons to scroll until you see “Delete”. Press the
OK button.
3. Double-click the button on the light module. The controller
screen will briefly display “Success” to confirm you have
removed the device from the controller key and system
network.
To remove the thermostat from the system network using
the controller:
1. Press and hold the Setup button on the controller until the
screen displays “Light Setup”. Press the OK button.
2. Use the arrow buttons to scroll until the screen displays
“Thermostat”. Press the OK button.
3. The control ler screen should now display “Add”. Use the
arrow buttons to scroll until you see “Delete”. Press the
OK button. The screen should now display “Setup
Waiting”.
4. Follow the device-specific directions for the thermostat
that you are removing from the system to trigger it.. The
controller screen will briefly display “Success” to confirm
you have removed it from the system network.
To delete the controller from the security panel (system):
1. Enter your panel into Delete mode.
2. Follow steps 2 to 5 in the instructions for “To add the
controller to the security panel (system):
” on page 9.
3. The controller screen will briefly di splay “Success” after
the controller has been successfully deleted from the
panel.
Lights and appliances
Plug-in Lamp Module or Plug-in Fluorescent
Light/Appliance Module
1. Plug in the device.
2. Enter Add mode on the security panel.
3. To add the device, double-click the button in the middle of
the light or appliance module. (If there is no beep at the
panel confirming successful enrollment of the device, try
pressing the button again.)
Tips
• Lamp modules cannot be used with compact fluorescent
bulbs (CFBs). Use appliance modules instead.
• Make sure the lamp to be controlled is plugged into the Z-
Wave side of the module (indicated by the Z-Wave logo).
• We recommend using a non-switched outlet for the
module. If using an outlet controlled by a switch, make
sure the outlet is switched on before sending light
commands.
• Keep lamps switch on to allow control through the Z-Wave
module, Alarm.com website, and mobile applications.
• Control dimming of lamp modules by pressing and holding
the button on the module, or through the Alarm.com
website
In-Wall Dimmer Light Switch or In-Wall On/Off Light Switch
1. Follow the provided directions to install the device and
ensure that it functions properly with manual on/off control.
2. Enter Add mode on the security panel.
3. To add the device, turn on and turn off the light switch. (If
there is no beep at the panel confirming successful
enrollment of the device, try turning the device on and off
again.)
Tips
• Dimmer switches and on/off switches cannot be
interchanged. Use the appropriate type of switch.
• If it is not practical to move the security panel 3 to 6 ft. to
the device, consider investing in a controller for
installations.
In-Wall Outlet Receptacle
1. Follow the provided directions to install the device and
ensure that it functions properly with manual control.
2. Enter Add mode on the security panel.
3. To add the device, double-click the button in the middle of
the outlet. (If there is no beep at the panel confirming
successful enrollment of the device, try double-clicking the
button again.)
Tips
• If it is not practical to move the security panel 3 to 6 ft. to
the device, consider investing in a controller for
installations.
• We recommend using a non-switched outlet for the Z-
Wave outlet. If using a switch outlet, make sure the outlet
is switched on before sending commands.