Great Planes Seawind .60-.91 ARF - GPMA1360 - Manual (Page 6)

6 6
KIT INSPECTION
Before starting to build, take an inventory of this kit to make sure it is complete, and inspect the parts to make sure they
are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you need assistance with assembly,
contact Product Support. When reporting defective or missing parts, use the part names exactly as they are written in
the Kit Contents list.
Great Planes Product Support
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
Telephone: (217) 398-8970, ext. 5
Fax: (217) 398-7721
E-mail: [email protected]
Parts Layout
1. Fuselage
2. Rudder
3. Canopy
4. Fuel Tank
5. Engine Mount
6. Airplane Stand
7. Cowl
8. Spinner
9. Main Fixed LG Mount (2)
10. Nose Gear Mounting Plate
11. Aileron & Flap Servo Covers
12. L&R Wing Tips
13. L&R Ailerons
14. L&R Flaps
15. L&R Wing Panels
16. Nose Gear
17. Main LG
18. Main LG Blocks
19. Throttle Servo Tray
20. L&R Wing Tip Supports 21. Main Wheels (3)
22. L&R Horizontal Stabilizer
23. Elevator
24. Aluminum Wing Joiner
25. Horizontal Stabilizer Tubes (2)
26. Water Rudder
27. Nose Gear Cover
28. Pushrods
29. Throttle Servo Hatch Cover
(8) Clevis
(2) CA Hinge Strip
(6) Large Control Horn
(34) #2 x 3/8" [9.5mm] Philips Screws
(7)
2-56 x 6" [152mm] Pushrod
Threaded One End
(8) Nylon FasLink
(8) 1/4" [6.4mm] Silicone
Clevis Retainer
(2) Screw-Lock Pushrod Connector
(2) 4-40 x 1/4" Socket-Head Cap Screw
(2) Nylon Retainer (for screw-lock
pushrod connector)
(2) #6 Flat Washer
(8) #8 Lock Washer
(8) 8-32 x 1" [25mm] Socket-Head
Cap Screw
(8) #8 SAE Flat Washer Plated
(8) #8 Split Ring Lock Washer Plated
(4) 8-32 Blind Nuts
(1) #4 x 5/8" [16mm] Sheet
Metal Screw
(5) #4 Flat Washer
(8) #2 Flat Washer
(9) 5/32" [4mm] Wheel Collar
(8) 6-32 x 1/8" [3mm] Set Screw
(4) Landing Gear Strap
(2) 6-32 x 3/4" [19mm] Pan Head Screw
(2) 6-32 Hex Nut
(1) 6-32 x 1/4" Socket Head Bolt
(1) Steering Arm
(8) #6 x 1/2" [13mm] Philips Sheet
Metal Screw
(1) 5/32 Nose Gear Bearing
(4) Metal Clevis 2-56 Threaded
(4) 2-56 Hex Nut
(2) Metal Retainer (for screw-lock
pushrod connector)
(1) 1200 x 10 x 2mm Foam Tape
(2) 1/4-20 Thumb screws
(1) Complete Water Bailer
(2) Steel Wing Alignment Pins
(1) Wheel Collar with Wire (for
steering mechanism)
(2) Hardwood Blocks (throttle servo)
(1) Retainer Plate (throttle servo)
(1) 25 x 25 x 0.8mm Double-Sided
Foam Tape (throttle servo)
(2) Threaded Cable Connectors
(2) Steering Cable
(1) 2.5mm Hex Wrench
not used
10 x 10 x 230mm Balsa Sticks
Kit Contents (Not Photographed)
Kit Contents
1
3
28
27
29
11
5
6
2
4
10
12
12 15 15
13 14 13 14
7
9
16
17
18 19
20
24
22 22
23
25
26
21
8