Display the tuner set up mode, Start auto program, Finish auto program – Philips VR650 User Manual
Page 22: Number buttons, Vcr ch(annel) up/down buttons, 22 re-setting your vcr’s tuner, Make sure, Adding and deleting a channel, Using the 100 button
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
22 Re-Setting Your VCR’s Tuner
T
o place receivable channels in your VCR (Video Cassette Recorder), follow steps 1-4 below. This function lets you re
program your VCR’s tuner at any time.With the Add/Delete feature you can add or delete any channel. You must use
your remote control.
I
Make sure... |---------------------------------------
• the steps on pages 7-8 have been completed, and your TV and
VCR are on.
• to make each entry within 60 seconds, otherwise the VCR will exit
the Tuner Set Up mode and you will have to start over.
Display the Tuner Set Up Mode
I First, press the MENU button to display the
main menu screen.
Now, press the NUMBER 3 button to select
“TUNER SET UP.”
The screen at right appears.
TO SELECT PUSH NO. SHOWN
1TV
[ON]
2CABLE TV
3 AUTO PROGRAMMING
4ADD;T)ELETE CH
5CH MEMORY REVIEW
6 TV STEREO [ON]
7 2ND AUDIO
TO END PUSH MENU
Start Auto Program
Press the NUMBER 3 button to start Auto
Programming. “AUTO SET PROCEEDING,
PLEASE WAIT” appears on the TV screen.
AUTO SET PROCEEDING
PLEASE WAIT
Finish Auto Program
I When auto program is complete, “AUTO SET COMPLETED”
appears on the TV screen, and then the lowest channel stored in the
VCR’s memory will appear on the TV screen. To view other stored
channels, press the VCR CH(annel) UP/DOWN buttons. Line mode
is always stored in the VCR’s memory. “L” appears on the VCR’s
front panel when selected using the VCR CH(aimel) UP/DOWN
buttons.
r-
Adding and Deleting a Channel
1. Press the MENU button to display the menu screen. Next, press
the 3 button to select “TUNER SET UP.”
2. Press the 2 button to change from “TV” to “CABLE TV.”
Press the 1 button to change from “CABLE TV” to “TV.”
“[ON]” appears beside your selection.
3. Press the 4 button to select the Add/Delete
chaimel feature. The display shown here
will appear.
4. Press two numbers to add or delete channels
up to 99. For 100 and higher, first press the
100 button, then two numbers.
• Always enter a “0” before any single-digit
entries. For example, 0, then 6 for “6.”
• Refer to “Using the 100 Button” to enter a
three-digit number.
5. Press the 1,2, or 3 button to “ADD,”
“DELETE,” or “SELECT ANOTHER CH”
that is in the VCR’s memoiy.
If “3” is selected, the display in step 3 will re-appear.
To exit the Add/Delete mode, press the MENU button once.
SELECT CHANNEL NUMBER
TO END PUSH MENU
TO SELECT PUSH NUMBER
1 ADD
2 DELETE
3 SELECT ANOTHER CH
TO END PUSH MENU
NUMBER Buttons
VCR CH(annel)
UP/DOWN Buttons
MENU Button
Channel Memory Review
First, press the MENU button. Next, press
the 3 button to select “TUNER SET UP.”
Now, press the 5 button to select “CH
MEMORY REVIEW.” The memorized
channel list will appear on the TV screen.
Now, press the 1 button to see the next
channel hst. Press the
2 button to see the
previous channel list
To exit, press the
MENU button.
^MEf.lORIZED CHANNEL: CABLE'
15
17 20
21
27
31
32
38
42
43
45
47
50
51
52
68
64
67
68
70
73
75
78
60
81
83
84
88
83
89
90
92
95 104 107 112
NEXr=1
PREVIOUS = 2
TO END PUSH MENU
)
Using the 100 Button
To select channel numbers 100 to 125 with
the NUMBER buttons, first press the 100
button and then enter the remaining two
numbers. For example for channel 105,
press NUMBER buttons 100,0,5.