beautypg.com
AT Commands for CX81801/CX06833/CX81300/CX06827 Modems Reference Manual
Conexant
102184B
5-12
Reporting Supported Range of Parameter Values
Command: +VLS=?
Response: ,,event>,, Where each event subparameter is a hex number the represents an event bit field of the reporting capabilities of each state. (see Table 5-6): Identifies the modem analog source/destination hardware configuration A made up of Primitives, , , and event>subparameters are the DCE event reporting capabilities for the Voice Transmit State, Voice Receive State, and the Voice Command State, respectively. Each of the event reporting subparameters is a hex number that represents an event bit field. The hex number format is defined in Table 5-6); a one in the bit field indicates that the DCE can report the associated event. Each of the possible hardware configurations has its own , ..., description line (the above form description shows just one). A terminates each description line. Example: AT+VLS=? 0," ",0000000000,0000000000,B084008000 1,"T",0B8418E000,0FE418E000,0B8419E000 2,"L",0884008000,0CE4008000,0884018000 3,"LT",0B8418E000,0FE418E000,0B8419E000 4,"S",0084008000,0484008000,3084018000 5,"ST",0B8418E000,0FE418E000,0B8419E000 6,"M",0084008000,04E4008000,3084008000 8,"S1",0084008000,0484008000,3084018000 9,"S1T",0B8418E000,0FE418E000,0B8419E000 11,"M1",0084008000,04E4008000,3084008000 13,"M1S1T",0B8418E000,0FE418E000,0B8419E000 14,"H",0084008000,04E4008000,3084018000 15,"HT",0B8418E000,0FE418E000,0B8419E000 19,"M1S1",0084008000,04E4008000,3084018000 20,"t",0B8418E000,0FE418E000,BB8419E000 Result Codes OK = 0-5,8-9,11,14,18-19. ERROR The value is out of range, or if the modem cannot service the request in the subparameter.
event>,,
Where each event subparameter is a hex number the represents an event bit field of the reporting capabilities of each state. (see Table 5-6):
Identifies the modem analog source/destination hardware configuration
A made up of Primitives,
, , and event>subparameters are the DCE event reporting capabilities for the Voice Transmit State, Voice Receive State, and the Voice Command State, respectively. Each of the event reporting subparameters is a hex number that represents an event bit field. The hex number format is defined in Table 5-6); a one in the bit field indicates that the DCE can report the associated event.
Each of the possible hardware configurations has its own , ..., description line (the above form description shows just one). A terminates each description line.
Example: AT+VLS=?
0," ",0000000000,0000000000,B084008000 1,"T",0B8418E000,0FE418E000,0B8419E000 2,"L",0884008000,0CE4008000,0884018000 3,"LT",0B8418E000,0FE418E000,0B8419E000 4,"S",0084008000,0484008000,3084018000 5,"ST",0B8418E000,0FE418E000,0B8419E000 6,"M",0084008000,04E4008000,3084008000 8,"S1",0084008000,0484008000,3084018000 9,"S1T",0B8418E000,0FE418E000,0B8419E000 11,"M1",0084008000,04E4008000,3084008000 13,"M1S1T",0B8418E000,0FE418E000,0B8419E000 14,"H",0084008000,04E4008000,3084018000 15,"HT",0B8418E000,0FE418E000,0B8419E000 19,"M1S1",0084008000,04E4008000,3084018000 20,"t",0B8418E000,0FE418E000,BB8419E000
Result Codes
OK
= 0-5,8-9,11,14,18-19.
ERROR
The value is out of range, or if the modem cannot service the request in the subparameter.
