Clarion ProAudio VRX 935VD VRX935VD - Manual (Page 52)

56
VRX935VD
English
Owner
’s
manual
●SPEAKER GAIN
This function sets speaker output level.
∗ This function is not available for speakers whose
“SPEAKER SEL” setting is set to OFF.
3-1. Touch the [SPEAKER GAIN] key to show
the submenu.
3-2. Touch the [FRONT L], [CENTER],
[FRONT R], [SURROUND R],
[SURROUND L] or [SUB WOOFER] key
to set respective item.
3-3. Touch the [ w] or [z] key to make
adjustments in the range -10 dB to +10 dB
in 1 dB step increments. The default value
is “0 dB”.
●DELAY
This function adjusts the timing of the speakers
so that they are synchronized with front speaker
output.
∗ This function is not available for speakers whose
“SPEAKER SEL” setting is set to OFF.
3-1. Touch the [DELAY] key to show the
submenu.
3-2. Touch the [CENTER SP] or [SURROUND
SP] key to set respective item.
3-3. Touch the [ w] or [z] key to adjust.
[CENTER SP]:
Adjustments are made in the range 0 ms
to 5 ms. The default value is “0 ms”.
[SURROUND SP]:
Adjustments are made in the range 0 ms
to 15 ms. The default value is “0 ms”.
●DOLBY D
This function sets the dynamic range
compression.
∗ This function is not available for speakers whose
“SPEAKER SEL” setting is set to OFF.
3-1. Touch the [DOLBY D] key to show the
submenu.
3-2. Touch the [MAX], [STD] or [MIN] key to
select respective item.
∗ The default value is “MAX”.
4. When all settings are completed, press the
[ADJ] button or touch the [RTN] key to
return to the previous mode.
●PL II Control
∗ This function is available only when the MUSIC
MODE is selected for Dolby PL II. For setup
details, see “Selecting the Dolby PL II (Dolby
Pro Logic II) type.”
3-1. Touch the [PL II CONTROL] key to show
the submenu.
3-2. Touch the [PANORAMA], [DIMENSION] or
[CENTER WIDTH] key to select respective
item.
[PANORAMA]:
Touch the [ON] or [OFF] key. “OFF” is the
default value.
[DIMENSION]:
Touch the [ w] or [z] key to make
adjustments between 0 and 6. The default
value is “3”.
[CENTER WIDTH]:
Touch the [ w] or [z] key to make
adjustments between 0 and 7. The default
value is “3”.
●FILTER
This function is used to select filter frequencies
that suit the speakers that are used.
∗ This function is not available for speakers whose
“SPEAKER SEL” setting is set to OFF.
3-1. Touch the [FILTER] key to show the
submenu.
3-2. Touch the [FRONT HPF], [CENTER HPF],
[SURROUND HPF] or [SUB WOOFER
LPF] key to set respective item.
3-3. Touch [ w] or [z] key to make settings.
[FRONT HPF]:
This function can be set to the following
four settings: 50 Hz, 80 Hz, 120 Hz or
THROUGH. “THROUGH” is the default
value.
[CENTER HPF]:
This function can be set to the following
three settings: 50 Hz, 80 Hz and 120 Hz.
“120 Hz” is the default value.
[SURROUND HPF]:
This function can be set to the following
four settings: 50 Hz, 80 Hz, 120 Hz or
THROUGH. “THROUGH” is the default
value.
[SUB WOOFER LPF]:
This function can be set to the following
three settings: 50 Hz, 80 Hz and 120 Hz.
“120 Hz” is the default value.
5.1ch Surround Decoder Operations