Braeburn 5050 - Manual (Page 4)

cont.
6 7
Setting Your Energy Saving Programs–Tips Before Starting
• It is important for you to set the current time of day (note the AM/PM in the display), and the
current day of week correctly to avoid problems with program execution. This must be done
prior to entering any programs.
• The heating and cooling programs have both separate setpoint times and setpoint temperatures.
• This thermostat is pre-programmed with weekday and weekend setpoint times and temperatures
recommended by the Environmental Protection Agency and the U.S. Department of Energy
in their ENERGY STAR® program. These settings provide efficient energy savings during normal
heating and cooling modes of operation. If you wish to use the settings in the table, no
further programming is necessary. Review these time and temperature settings prior to
establishing your personal program settings to maximize your savings, and minimize
programming requirements.
PROGRAMMING
4
Programming Overview for 7 Day Programming Mode
(Programming switch set to 7 day—see installation section)
You can select one of three Quick Program Groups or Individual Day programming to allow
you to change the daily setpoint times and temperatures to meet your individual schedule
needs. The Quick Program Groups can be used to set the main portion of your schedule,
allowing you to later modify specific days of the week as required using the Individual Day
programming capabilities.
Once you enter program mode, you can select the Quick Program Group or Individual Day
Programs as you desire.
Setting the Recirculating Fan Cycle (see also section 5.7)
13. Press the or button to change the
Recirculating Fan off cycle to the desired value of
120, 60 or 40 minutes.
14. Press the RETURN button again to return to the normal mode, or wait 15 seconds for the
thermostat to return automatically.
Whole Week – allows you to program all seven days (M, TU, W, TH, F, SA, SU will show in
display) at the same time. Then you can use individual day programming to fine tune your
program for the few setpoint times or temperatures that you may wish to change.
Weekday – allows you to program all the weekdays (M, TU, W, TH, F will show in display) at
the same time. Then go to Weekend group mode to finish programming your weekend
setpoint times and temperatures. Individual day programming can be used to fine tune your
settings to match your daily needs.
• Make sure you place the system switch in the HEAT or COOL modes of operation as appropriate.
You should not enter a program in the OFF position.
• When the system switch is in the COOL or HEAT modes of operation, the appropriate indicator
will appear in the LCD display when the system is running. When the system switch in the OFF
mode, the display will indicate OFF.
NOTE:
If the 7 day programming mode was selected using the slide switch on the circuit
board during installation (section 2.2), the default program will use the weekday times and
temperatures shown above for all 7 days. The programming mode can be switched between
weekday-weekend and 7 day at any time by removing the thermostat from the base, and
following steps 19-21 in section 2.2, then pressing the reset button. All settings must then
be reentered starting with section 4.2.
12. After pressing the RETURN button again, the display
will show " XXX OC SET", where XXX is the
Recirculating Fan off cycle.
Entering Your Program
cont.
PROGRAMMING
4
Weekday Weekend
MORN
DAY
EVE
NIGHT
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 83˚ F (28˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
Programming Overview for 7 Day Programming Mode cont.
Weekend – allows you to program the weekend days (SA, SU will show in the display) at
the same time. Again, individual day programming can be used to change specific setpoint
times or temperatures
Individual Days – allows you to program each day of the week individually to give you
the greatest schedule flexibility. Often used to fine tune programming after initially
programming the thermostat using Whole Week, Weekday or Weekend groups.
IMPORTANT NOTE: When in group selection, the
thermostat will check if all of the days of that group
have the same program setpoint times and
temperatures. If so, the time and temperature of the
individual setpoint ( MORN, DAY, EVE, NIGHT) will
be displayed.
Otherwise, the individual setpoint time and temperature will be blanked. User is allowed to
change the daily programs for this setpoint time and temperature by pressing the or
button. This will reset all the daily programs of the group for that specific individual setpoint
( MORN, DAY, EVE, NIGHT) time and temperature to the startup default for that setpoint.
Continued pressing of the or button by the user will change setpoint time and
temperature settings as desired.
3. If you wish to use a different Quick Program Group or Individual Day program mode,
you can change by pressing the DAY/TIME button to select another group in the
following sequence, Whole Week - Weekday - Weekend - Monday - Tuesday -
Wednesday - Thursday - Friday - Saturday - Sunday - Whole Week.
4. Once you have finished your Quick Program Group or Individual Day selection, press
the or button to change the time to the desired hour in one hour increments. Press
the PROG button. The minute portion of the setpoint time will begin flashing.
5. Press the or button to change the time to the desired minute in 10-minute
increments. Press PROG button. The SET TEMP will begin flashing.
6. Press the or button to change the setpoint temperature to the desired setting in
1˚ F increments (0.5˚ C). Press PROG button to save. The thermostat will now display
the DAY setpoint time and temperature. Again, you will see the hour portion of the
setpoint time and the AM/PM indicator will be flashing.
7. Follow steps 4 through 6 to set the set point times and temperatures for the MORN,
DAY, EVE and NIGHT setpoints for the Quick Program Group or Individual Day selection
for the HEAT mode.
1. Place the system switch in the HEAT mode
of operation.
2. Press the PROG button to enter Program setting
mode. The MORN setpoint of the Whole Week
Quick Program Group will be displayed. The
display will show M, TU, W, TH, F, SA, SU,
indicating the whole week is being programmed.
The hour portion of the setpoint time and the AM/PM indicator will be flashing.
4.4