Braeburn 2200 - Manual (Page 4)

6
Setting the Extended Hold Time (see also section 7) • It is important for you to set the current time of day (note the AM/PM indicator
in the display), and the current day of week correctly to avoid problems with
program execution. This must be done prior to entering any program settings.
• The heating and cooling programs have both separate set point times and
set point temperatures.
• This thermostat is preprogrammed with weekday and weekend set point times
and temperatures. These settings provide efficient energy savings during normal
heating and cooling modes of operation. If you wish to use the settings in the
table, no further programming is necessary. Review these time and temperature
settings prior to establishing your personal program settings to maximize your
savings, and minimize programming requirements.
• Make sure you place the system switch in the HEAT or COOL modes of
operation as appropriate. You should not enter a program in the OFF position.
• When the system switch is in the COOL or HEAT modes of operation, the
appropriate indicator will appear in the LCD display when the system is running.
When the system switch is in the
OFF mode the display will indicate OFF.
Programming Overview
Your thermostat contains separate Weekday and Weekend Program Groups that
allow you to change the daily set point times and temperatures to meet your
individual schedule needs.
Weekday - allows you to program all the weekdays (M, TU, W, TH, F will show in
display) at the same time. Allows programming times and temperature settings for
four set points (MORN, DAY, EVE and NIGHT) to meet your weekday schedule needs.
Weekend - allows you to program all the weekend days (SA, SU will show in the
display) at the same time. Again allows programming times and temperature
settings for four set points (MORN, DAY, EVE and NIGHT) to meet your weekend
schedule needs.
Entering Your Program
1. Place the system switch in the HEAT
mode of operation.
2. Press the PROG button to enter Program
setting mode. The
MORN set point of
the Weekday Program Group will be
displayed. The display will show
M, TU,
W, TH, F to indicate the Weekday group is being programmed. The hour portion
of the set point time and the AM/PM indicator will be flashing.
cont.
Programming User Settings
The default setting is Long (indefinite) Hold.
If the HOLD feature is activated, the current
set point will be held until HOLD is released.
1. In normal operating mode, press and
hold the
RETURN button for 4 seconds.
Press RETURN again to skip past
differential setting. The display will show “ HOLD LG”, where LG is indefinite hold.
2. Press the or button to change the Extended Hold time from indefinite (LG)
to 24 hours (
SH).
3. Press the RETURN button again to set the Filter Check Monitor or wait 30
seconds for the thermostat to return to the normal mode.
Setting Filter Check Monitor (see also section 7)
The default setting is 0 days (Filter monitor
disabled).
1. In normal operating mode, hold the
return button for 4 seconds. Press
RETURN button repeatedly until “XXX
SET FILT” is shown where XXX is the Filter Monitor interval.
2. Press the or button to change the Filter Monitor interval to the desired
value of 0 (disabled), 30, 60, 90, 120, or 180 days.
3. Press the RETURN button again to set the Adaptive Recovery Mode or wait
30 seconds for the thermostat to return to the normal mode.
Setting Adaptive Recovery Mode (ARM™) (see also section 7)
The default setting is OFF (Adaptive
Recovery Mode disabled).
1. In normal operating mode, press and
hold the
RETURN button for 4 seconds.
Press RETURN repeatedly until “SET
XXX” is shown where XX is the Adaptive
Recovery Mode.
2. Press the or button to change the Adaptive Recovery Mode to either
ON or OFF.
3. Press the RETURN button again or wait 15 seconds for the thermostat to
return to the normal mode.
Setting Your Energy Saving Programs – Tips Before Starting
• It is important for you to set the current time of day (note the AM/PM
indicator in the display), and the current day of week correctly to avoid
problems with program execution. This must be done prior to entering any
program settings.
• The heating and cooling programs have both separate set point times and
set point temperatures.
Setting Your Energy Saving Program
4 5
7