KEYENCE CV-X290 - Manual (Page 3)

3
With CA-EC80L installed
With CA-EC80LJ installed
ቢ Parallel I/O connector
Use to connect the parallel input/output signals.
ባ SD2 slot (upper), SD1 slot (lower)
Insert an SD card.
The lower slot (SD1) holds the included SD card (1 GB) by factory default.
ቤCamera slot
Use to connect the camera input unit.
(At the time of shipping, nothing is inserted in the slot.)
ብUSB connector for the dedicated mouse
Use to connect the included dedicated mouse.
ቦRGB output terminal
Use to connect to an external monitor.
ቧUSB connector
Use to connect a USB cable.
ቨExpansion unit connector 1 (right side)
Use to connect the camera expansion unit (CA-E800).
ቩCamera 1 connector
Use to connect camera 1.
ቪTOUCH PANEL port
Use to connect an optional RS-232C cable for the touch panel (OP-
87258: 3m/OP-87259: 10m).
ቫRS-232C port
Use to connect an optional RS-232C communication cable (OP-26487:
2.5m) or an optional RS-232C modular cable for touch panels
(OP-87264: 3m/OP-87265: 10m).
ቭETHERNET connector
Use to connect an Ethernet cable.
ቮTerminal block
Use for signal input and output.
ቯPower and ground terminals
Use to connect power (24 V DC) and the ground wire.
ተExpansion unit connector 2 (left side)
Use to connect the illumination expansion unit CA-DC10E, CA-DC21E, or
CA-DC30E.
ቱCAMERA1 connector
Use to connect the LJ-V as camera 1.
Install the controller unit to DIN rail, or use the holes on the bottom of the
controller to secure it with screws.
Caution on Direction of Controller Mounting
• Install the controller in the direction indicated by the circle shown below.
Do not install the controller in any other direction.
• For ventilation, keep the space free of objects for 50 mm or more above
the controller and 50 mm or more for both sides. Keep the space free of
objects for 90 mm or more in the front of the connector panel in order to
connect the cables safely.
• When two or more controllers are installed side by side, maintain 50
mm or more of space between the controllers, and 50 mm or more
above both controllers.
(Provide the same space when the controller and an LJ-V controller are
installed side by side.)
Identifying Controls and Connectors
SD Card 1 must be inserted while the device is operating.
The USB port is used exclusively for the dedicated mouse (OP-
87506).
Connecting other equipment including a commercial USB
mouse can cause a malfunction or damage to the controller or
connected devices.
Important
NOTICE
Installing the Controller Unit
• Do not install the controller in a location with lots of dust or
water vapor.
The controller does not have a mechanism to protect it from
dust or water. Dust or water entering the controller can cause
damage to the controller.
• Turn off the power to the controller when connecting or
removing an expansion unit, a cable, or a terminal block.
Connecting or removing the camera expansion unit, the
cable, or the terminal block while the power is being supplied
may damage the controller or peripheral devices.
• When an expansion unit is not connected, place the
connector protection cover back on the controller. Using the
controller with the connector exposed may cause damage to
the controller.
• Do not block the ventilation openings on the top and bottom
of the controller. If the vents are blocked, heat will
accumulate inside the controller and can cause a system
failure.
• When installing the controller on a surface, pierce holes in
the surface at the positions of the ventilation openings on the
bottom of the controller or perform similar operations to
ensure that there is ventilation from the bottom of the
controller to the top.
• If the temperature inside the control panel (temperature at
the bottom of the controller) exceeds the rating, use forced
air-cooling or increase the free space around the system to
improve ventilation until the operating ambient temperature
decreases below the rating.
NOTICE
50 mm
50 mm 50 mm
50 mm
50 mm
NOTICE