Main specifications – KEYENCE XG-7000 Series User Manual

Page 7

*1 Models equipped with the Ethernet port in the CPU unit support Ethernet port direct connection.
*2 When either one is turned ON, at the time of maximum load including the input current.

Main Specifications

Model type

NPN type

XG-7701/7702

XG-7501/7502

XG-7001/7002

XG-7001A/7002A

PNP type

XG-7701P/7702P

XG-7501P/7502P

XG-7001P/7002P

—————

Pixels

• With CA-HX500C/HX500M connected

5 mega-pixel mode: 2432(H) x 2040(V),
approx. 4.96 mega-pixels
2 mega-pixel mode: 1600(H) x 1200(V),
approx. 1.92 mega-pixels

• With CA-HX200C/HX200M connected

2 mega-pixel mode: 1600(H) x 1200(V),
approx. 1.92 mega-pixels

• With CA-HX048C/HX048M connected

470 k pixel mode: 784(H) x 596(V),
approx. 470,000 pixels
310 k pixel mode: 640(H) x 480(V),
approx. 310,000 pixels
240 k pixel mode: 512(H) x 480(V),
approx. 240,000 pixels

• With XG-H500C/H500M connected

5 mega-pixel mode: 2432(H) x 2050(V),
approx. 4.99 mega-pixels

• With XG-200C/S200C/H200C/200M/

S200M/H200M connected
2 mega-pixel mode: 1600(H) x 1200(V),
approx. 1.92 mega-pixels
1 mega-pixel mode: 1024(H) x 960(V),
approx. 980,000 pixels

• With XG-H100C/H100M connected

1000(H) x 1000(V), 1 mega-pixel

• With XG-035C/S035C/H035C/035M/

S035M/H035M connected
310 k pixel mode: 640(H) x 480(V),
approx. 310,000 pixels
240 k pixel mode: 512(H) x 480(V),
approx. 240,000 pixels

• With CA-HX200C/HX200M connected

2 mega-pixel mode: 1600(H) x 1200(V),
approx. 1.92 mega-pixels

• With CA-HX048C/HX048M connected

470 k pixel mode: 784(H) x 596(V),
approx. 470,000 pixels
310 k pixel mode: 640(H) x 480(V),
approx. 310,000 pixels
240 k pixel mode: 512(H) x 480(V),
approx. 240,000 pixels

• With XG-200C/S200C/H200C/200M/

S200M/H200M connected
2 mega-pixel mode: 1600(H) x 1200(V),
approx. 1.92 mega-pixels
1 mega-pixel mode: 1024(H) x 960(V),
approx. 980,000pixels

• With XG-H100C/H100M connected

1000(H) x 1000(V), 1 mega-pixel

• With XG-035C/S035C/H035C/035M/

S035M/H035M connected
310 k pixel mode: 640(H) x 480(V),
approx. 310,000 pixels
240 k pixel mode: 512(H) x 480(V),
approx. 240,000 pixels

• With CA-HX048C/HX048M connected

470 k pixel mode: 784(H) x 596(V),
approx. 470,000 pixels
310 k pixel mode: 640(H) x 480(V),
approx. 310,000 pixels
240 k pixel mode: 512(H) x 480(V),
approx. 240,000 pixels

• With XG-035C/S035/H035C/035M/

S035M/H035M connected
310 k pixel mode: 640(H) x 480(V),
approx. 310,000 pixels
240 k pixel mode: 512(H) x 480(V),
approx. 240,000 pixels

640(H) x 480(V), approx. 310,000 pixels

Camera
input

Two color/monochrome cameras
(Compatible with
CA-HX500C/HX500M/HX200C/HX200M/
HX048C/HX048M and XG-H500C/200C/
S200C/H200C/H100C/035C/S035C/
H035C/H500M/200M/S200M/H200M/
H100M/035M/S035M/H035M, mixed
connection possible)

Two color/monochrome cameras
(Compatible with
CA-HX200C/HX200M/HX048C/HX048M
and XG-200C/S200C/H200C/H100C/
035C/S035C/H035C/200M/S200M/
H200M/H100M/035M/S035M/H035M,
mixed connection possible)

Two color/monochrome cameras
(CA-HX048C/HX048M and XG-035C/
S035C/H035C/035M/S035M/H035M can
be connected. Mixed connection is
possible.)

Two monochrome cameras (CA-CM20:
KEYENCE or
• XC-HR50/XC-HR57/XC-56/XC-ST50/

XC-ES50/XC-ES51/XC-EI50/XC-EI30/
XC-EU50: Sony

• CS8550Di/CS8570D/CS8560D:

Toshiba Terry)

Two extra cameras and up to four cameras can be connected by using expansion unit XG-E700.

Two extra cameras and up to four cameras
can be connected by using expansion unit
XG-E700A.

Trigger input

4-camera simultaneous capture/individual capture can be selected (when XG-E700 is not connected, images from up to two cameras
can be captured at the same time)

4-camera simultaneous capture/individual
capture can be selected (when XG-E700
is not connected, images from up to two
cameras can be captured at the same
time)

Main image processor

DSP (High-speed)

DSP

DSP (High-speed)

Registered number of inspection settings

SD cards 1 and 2 can each hold 1000 programs (depending on the size of the SD card and the size of the programs), external switching possible

Number of registered screens

Maximum 1000 screens for each program (depending on SD card size),Image compression also available.

SD card

• SD card slot x 2 (SDHC compatible)
• Compatible with OP-87133 (512MB),

CA-SD1G (1GB: installed standard to
SD1), and CA-SD4G (4GB: SDHC)

• SD card slot x 2 (SDHC compatible)
• Compatible with OP-87133 (512MB: installed standard to SD1), CA-SD1G (1GB), and CA-SD4G

(4GB: SDHC)

Interface

Controlled input (compatible with
arbitrary assignment)

• 20 input (including four high speed designed for trigger input)
• Input rating 26.4 V or lower, 2 mA or grater (3 mA or grater for high speed input terminal)

Controlled output (compatible
with arbitrary assignment)

• 28 output (including four high speed outputs designed for pulse outputting to external device)
• NPN type: NPN open collector Maximum 50 mA (30 V or less) PNP type: PNP open collector 50 mA (30 V or less)

Monitor output

Analog RGB output, SVGA 800 x 600 (24 bit color, 60 Hz)

Operation indicators

Power, Error LED display

RS-232C

Numerical value output and control input/output enabled, maximum baud rate of 115200 bps is supported (Cannot be used with the CA Series Touch Panel)

PLC link

• Numerical value output and control input/output using the RS-232C port or Ethernet port enabled (Do not use to connect to CC-Link, EtherNet/IP and PROFINET. The RS-232 Port

cannot be used with the CA Series Touch Panel.)

• Following PLCs are supported via link unit:

KEYENCE: KV-700 Series, KV-1000 Series, KV-3000 Series, KV-5000 Series, KV-5500 Series
Mitsubishi Electric: MELSEC A Series (RS-232C only), Q Series, L Series
OMRON: SYSMAC C Series (RS-232C only), CP1/CS1/CJ1/CJ2 Series
YASKAWA Electric: MP900 Series (RS-232C only), MP2000 Series

Ethernet

• Numerical value output, and control input/output enabled.
• By the connection of KEYENCE PC application software, in addition to the function described above, uploading and downloading the inspection settings, simulations, data,

including image data can be sent or received.

• VisionDatabase function support (sold separately)
• For the FTP client function, the VNC server function (for clients other than for PC it will be only for the screen display), and BOOTP function.
• 1000BASE-T/100BASE-TX/10BASE-T

USB

• By the connection of KEYENCE PC application software, in addition to numerical value output and control input/output , uploading and downloading the inspection settings,

simulations, data, including image data can be sent or received

• VisionDatabase function support (sold separately)
• USB2.0

CC-Link

• By connecting the optional CC-Link expansion unit CA-NCL10E, numerical value input/output and control input/output are enabled. (Do not use to connect to PLC Link,

EtherNet/IP and PROFINET.)

• Compatible to the Ver.1.10 remote device station, Ver.2.00 remote device station

EtherNet/IP

Numerical value input/output, and control input/output by using the Ethernet port enabled. (Do not use to connect to PLC Link, CC-Link and PROFINET.)
• Compatible to the cyclic communication (max.1436 byte), and message communication
• Maximum number of connections 32
• Compatible with the conformance test Version.A7

PROFINET

Numerical value input, and control input/output by using the Ethernet port enabled.
• Compatible to the cyclic communication (max. 1408 byte)

• Compatible to the aperiodic (recorded data) communication

• Compatible with the Conformance Class A

• Do not use to connect to PLC Link, CC-Link and EtherNet/IP.

Console

• By the optional OP-84231, OP-84236 (without silk screen printing), various menu can be used
• Compatible to the operation assignment settings to the console button
• Compatible to the button activation and deactivation of each user group

Touch Panel

• Setting operation from the CA Series touch panel used by the RS-232 port is possible
• For the dedicated touch menu or the operation button (Cannot be used with no protocol communication using the RS-232C or with the PLC Link)

Display language

Japanese/English/Simplified Chinese/Traditional Chinese/German selectable

Illumination control

By connecting the optional illumination expansion unit CA-DC30E/DC20E/DC21E, LED illumination (12 V, 24 V) and intensity control are enabled.

Rating

Power supply voltage

24 VDC positive and negative to 10%

Current consumption

• 2.4 A (2 Cameras)

• 3.2 A (4 Cameras)

• 2.2 A (2 Cameras)

• 2.8 A (4 Cameras)

• 2.2 A (2 Cameras)

• 2.6 A (4 Cameras)

Environment
al resistance

Ambient temperature

• With two cameras connected: 0 to +50°C

(0 to +45°C with min. 1 mega-pixel camera connected)

• With four cameras connected: 0 to +45°C

0 to +50°C

0 to +50°C (With four cameras connected:
0 to +45°C)

Ambient operating humidity

35 to 85% RH (no condensation)

Weight

Approx. 1250 g

Approx. 1300 g