Checkline 3000FX Series - Manual (Page 9)

- 9 -
5. Press the ▼ key to select the on or off states.
6. Press
OK to confirm your selection
3.5 Manually Setting Measurement Mode (DCFN only)
In some cases, especially with varnish applied to zinc on steel,
it is advisable to manually set the measuring mode—F mode
(Ferrous) for measurements on steel/iron, N mode (Non-
Ferrous) for measurements on non-ferrous metals.
1. Press ▼ repeatedly until display shows Options.
2. Press
OK . Measuring Unit appears on the display.
3. Press ▼ repeatedly until Measuring Mode appears.
4. Press
OK . Auto FN Identifications appears.
5. Press ▼ repeatedly until either Ferrous (F) or
Non-Ferrous (N) or Auto FN appears on the display.
6. Press OK to confirm the measurement mode that you want
to activate. The display shows - - - - and either Auto FN
or Ferr or Non-Ferr. See diagram of dsiplay on page 3.
3.6 Total Reset To Factory Defaults
This procedure deletes all single and statistical values. It also
deletes set calibration values and optional items and resets the
gauge to the factory default.
1. Switch off the gauge
2. Press and hold the
ESC key (item E, page 4). At the
same time turn the power back on.
3. An acoustic signal will sound and all factory default
settings are restored.
4. Release both keys and the gauge will restart with all
factory default settings restored.
- 20 -
• Do not expose the window of the infrared adapter to direct solar
radiation.
• Do not operate any filament and halogen lamps in the immediate
vicinity of the adapter. The distance between adapter and lamp
should be more than 1 meter.
• The infrared windows of the test instrument and of the adapter
must be parallel and facing each other at a distance of around
30 cm to 50 cm.
After pressing OK to start infrared data transmission, keep the
gauge´s infrared window pointed at the IR adapter as long as the
green LED is lit.
- 9 -
5. Press the ▼ key to select the on or off states.
6. Press
OK to confirm your selection
3.5 Manually Setting Measurement Mode (DCFN only)
In some cases, especially with varnish applied to zinc on steel,
it is advisable to manually set the measuring mode—F mode
(Ferrous) for measurements on steel/iron, N mode (Non-
Ferrous) for measurements on non-ferrous metals.
1. Press ▼ repeatedly until display shows Options.
2. Press
OK . Measuring Unit appears on the display.
3. Press ▼ repeatedly until Measuring Mode appears.
4. Press
OK . Auto FN Identifications appears.
5. Press ▼ repeatedly until either Ferrous (F) or
Non-Ferrous (N) or Auto FN appears on the display.
6. Press OK to confirm the measurement mode that you want
to activate. The display shows - - - - and either Auto FN
or Ferr or Non-Ferr. See diagram of dsiplay on page 3.
3.6 Total Reset To Factory Defaults
This procedure deletes all single and statistical values. It also
deletes set calibration values and optional items and resets the
gauge to the factory default.
1. Switch off the gauge
2. Press and hold the
ESC key (item E, page 4). At the
same time turn the power back on.
3. An acoustic signal will sound and all factory default
settings are restored.
4. Release both keys and the gauge will restart with all
factory default settings restored.
- 20 -
• Do not expose the window of the infrared adapter to direct solar
radiation.
• Do not operate any filament and halogen lamps in the immediate
vicinity of the adapter. The distance between adapter and lamp
should be more than 1 meter.
• The infrared windows of the test instrument and of the adapter
must be parallel and facing each other at a distance of around
30 cm to 50 cm.
After pressing OK to start infrared data transmission, keep the
gauge´s infrared window pointed at the IR adapter as long as the
green LED is lit.