Checkline 3000FX Series - Manual (Page 14)

- 14 -
set as a negative offset value. The instrument will then display
the coating thickness above the peaks of the rough surface.
Setting Zero Offset Value
1. Press ▼ . Calibration appears on the display’
2. Press OK . Zero Setting appears on the display
3. Press ▼ twice. Zero Offset appears on the display.
4. Press
OK . Offsets appears on the display.
5. Press OK . Set Offset Value appears on the display.
6. Press ▼ or ▲ repeatedly until the required offset value
appears on the display.
7. Press OK . Offset Has Been Set appears on the display
briefly, followed by the start display with - - - -.
Deleting Zero Offset Value
1. Press ▼ Calibration appears on the display
2. Press
OK . Zero Setting appears on the display
3. Press ▼ twice. Zero Offset appears on the display
4. Press
OK . Setting of Offset appears on the display
5. Press ▼. Deletion of Offset appears on the display
6. Press
OK . Offset Deleted appears briefly, followed by
the start display with the four dashes - - - -.
- 15 -
5 .0 S ET T I N G A U DI BLE L I M I T A LERT S
To monitor your measured values, you can set an upper and a lower
limit value. This setting is useful during the measurement, for the
evaluation of the measured values later when displaying the single
values or for the printout of measured values If the limit value is
exceeded or if it's not reached, an audio signal will sound, and a
warning note will appear on the display (_ or _).
Setting
1. Press ▼ repeatedly until Limits appears on the display
2. Press
OK . Limits Setting appears on the display.
3. Press OK again. Set Lower Limit appears.
4. Press ▼ or ▲ repeatedly until the desired lower limit value
appears on the display.
5. Press OK . Set Upper Limit appears on the display.
6. Press ▼ or ▲ repeatedly until the desired upper limit value
appears on the display.
7. Press OK . Limits have been set will appear briefly, then the
start screen with - - - -.
Deleting
1. Press ▼ repeatedly until Limit s appears on the display.
2. Press
OK . Limits Setting appears
3. Press ▼ until Deletion of Limits appears
4. Press
OK . Limits Deleted appears briefly, followed by the
start screen with - - - -.
- 14 -
set as a negative offset value. The instrument will then display
the coating thickness above the peaks of the rough surface.
Setting Zero Offset Value
1. Press ▼ . Calibration appears on the display’
2. Press OK . Zero Setting appears on the display
3. Press ▼ twice. Zero Offset appears on the display.
4. Press
OK . Offsets appears on the display.
5. Press OK . Set Offset Value appears on the display.
6. Press ▼ or ▲ repeatedly until the required offset value
appears on the display.
7. Press OK . Offset Has Been Set appears on the display
briefly, followed by the start display with - - - -.
Deleting Zero Offset Value
1. Press ▼ Calibration appears on the display
2. Press
OK . Zero Setting appears on the display
3. Press ▼ twice. Zero Offset appears on the display
4. Press
OK . Setting of Offset appears on the display
5. Press ▼. Deletion of Offset appears on the display
6. Press
OK . Offset Deleted appears briefly, followed by
the start display with the four dashes - - - -.
- 15 -
5 .0 S ET T I N G A U DI BLE L I M I T A LERT S
To monitor your measured values, you can set an upper and a lower
limit value. This setting is useful during the measurement, for the
evaluation of the measured values later when displaying the single
values or for the printout of measured values If the limit value is
exceeded or if it's not reached, an audio signal will sound, and a
warning note will appear on the display (_ or _).
Setting
1. Press ▼ repeatedly until Limits appears on the display
2. Press
OK . Limits Setting appears on the display.
3. Press OK again. Set Lower Limit appears.
4. Press ▼ or ▲ repeatedly until the desired lower limit value
appears on the display.
5. Press OK . Set Upper Limit appears on the display.
6. Press ▼ or ▲ repeatedly until the desired upper limit value
appears on the display.
7. Press OK . Limits have been set will appear briefly, then the
start screen with - - - -.
Deleting
1. Press ▼ repeatedly until Limit s appears on the display.
2. Press
OK . Limits Setting appears
3. Press ▼ until Deletion of Limits appears
4. Press
OK . Limits Deleted appears briefly, followed by the
start screen with - - - -.