Checkline 3000FX Series - Manual (Page 3)

- 3 -
2 .0 O V ERV I EW
2.1 Display
If this symbol flashes, the batteries have to be
changed, see page 9.
-------- Appears if limit values are exceeded or not reached
ZERO Appears when Zero calibration is complete.
If flashing: ZERO setting begun but not completed.
CAL Appears when Foil calibration is complete.
If flashing: CAL setting begun but not completed.
LIMIT Appears if Limit values have been set.
If flashing: LIMIT setting begun but not completed.
AUTO FN Appears when automatic ferrous / non-ferrous
measuring mode is active.
Ferr Appears when ferrous measuring mode is active.
Non-Ferr Appears when non-ferrous measuring mode is active.
µm All measured values given in µm unit.
mils All measured values given in mils unit.
ZERO ER
Non- Non-
Ferr Ferr
mils mils
µ
mm mm
AUTO F/ N F CALLIM IT LIM IT
- 26 -
1/4 CALIBRATION
1/4 Zero Setting
2/4 Foil Calibration
3/4 Zero Offset
1/2 Offset setting
2/2 Delection of Offset
4/4 Deletion of Calibration
1/1 Works Calibration Activated
2/4 STATISTICS
1/5 Print Out of Statistics
2/5 Print Out of Measurements
3/5 Display of Statistics
4/5 Display of Measurements
5/5 Delection of Statistics
3/4 LIM ITS
1/2 Limit Setting
1/2 Set Lower Limit
2/2 Set Upper Limit
2/2 Deletion of Limits
4/4 OPTIONS
1/9 Measuring Unit
1/2
µ m
2/2 mils
2/9 Measuring Mode
1/3 Auto FN Ident
2/3 Ferrous (F)
3/3 Non-Ferrous (N)
3/9 Switch Off Mode
1/2 Auto
2/2 Permanent
4/9 Backlight
1/3 Off
2/3 3 Secs
3/3 Permanent
5/9 Beeper
1/2 On
2/2 Off
6/9 Online Statistics
1/2 Mean & Stad. Dev.
2/2 Max and Min
7/9 Welcome Test
1/2 On
2/2 Off
8/9 Power Supply
1/2 Batteries
2/2 Rechargeable Batteries
9/9 Language
1/3 English
2/3 Espanol
3/3 Francais
A PPEN DI X : D I AGRAM OF M EN U S T RU CT U RE
After turning on the instrument, press ▲ or ▼ repeatedly to move to
the desired main section (Calibration, for example). Next, press
OK
to access the second level subsections within the main section. Press
▼ to scroll through the second level subsections and
OK to select
one. Use the same technique of pressing ▲ or ▼ and OK to access
third level subsections; use ESC to move back to the next higher
level up to the - - - - screen, delete the last reading immediately after
taking it and interrupt a setting action.
- 3 -
2 .0 O V ERV I EW
2.1 Display
If this symbol flashes, the batteries have to be
changed, see page 9.
-------- Appears if limit values are exceeded or not reached
ZERO Appears when Zero calibration is complete.
If flashing: ZERO setting begun but not completed.
CAL Appears when Foil calibration is complete.
If flashing: CAL setting begun but not completed.
LIMIT Appears if Limit values have been set.
If flashing: LIMIT setting begun but not completed.
AUTO FN Appears when automatic ferrous / non-ferrous
measuring mode is active.
Ferr Appears when ferrous measuring mode is active.
Non-Ferr Appears when non-ferrous measuring mode is active.
µm All measured values given in µm unit.
mils All measured values given in mils unit.
ZERO ER
Non- Non-
Ferr Ferr
mils mils
µ
mm mm
AUTO F/ N F CALLIM IT LIM IT
- 26 -
1/4 CALIBRATION
1/4 Zero Setting
2/4 Foil Calibration
3/4 Zero Offset
1/2 Offset setting
2/2 Delection of Offset
4/4 Deletion of Calibration
1/1 Works Calibration Activated
2/4 STATISTICS
1/5 Print Out of Statistics
2/5 Print Out of Measurements
3/5 Display of Statistics
4/5 Display of Measurements
5/5 Delection of Statistics
3/4 LIM ITS
1/2 Limit Setting
1/2 Set Lower Limit
2/2 Set Upper Limit
2/2 Deletion of Limits
4/4 OPTIONS
1/9 Measuring Unit
1/2
µ m
2/2 mils
2/9 Measuring Mode
1/3 Auto FN Ident
2/3 Ferrous (F)
3/3 Non-Ferrous (N)
3/9 Switch Off Mode
1/2 Auto
2/2 Permanent
4/9 Backlight
1/3 Off
2/3 3 Secs
3/3 Permanent
5/9 Beeper
1/2 On
2/2 Off
6/9 Online Statistics
1/2 Mean & Stad. Dev.
2/2 Max and Min
7/9 Welcome Test
1/2 On
2/2 Off
8/9 Power Supply
1/2 Batteries
2/2 Rechargeable Batteries
9/9 Language
1/3 English
2/3 Espanol
3/3 Francais
A PPEN DI X : D I AGRAM OF M EN U S T RU CT U RE
After turning on the instrument, press ▲ or ▼ repeatedly to move to
the desired main section (Calibration, for example). Next, press
OK
to access the second level subsections within the main section. Press
▼ to scroll through the second level subsections and
OK to select
one. Use the same technique of pressing ▲ or ▼ and OK to access
third level subsections; use ESC to move back to the next higher
level up to the - - - - screen, delete the last reading immediately after
taking it and interrupt a setting action.