Panasonic PV-7451 - Manual (Page 26)

VCR
Uh
VCR Plus+ Programming
1^^Before you begin, make sure...
n ______ _____
n The clock is set.
□ VCR Plus+ Setup is complete
(see pages 24, 25).
Multi Function Display
_ © © ©
0 © ©
" __ I МЕЮ.Г
© |©| ^
SPEED
s u
■Mr Ю«....
i
ADD/
DELETE
J
Use normal Timer Recording steps if:
• the PlusCode for a program is not listed.
• you anticipate the program, such as a sporting
event, to run over the scheduled stop time.
See page 19 to:
• cancel a timer recording in progress.
• replace program contents.
• reviewf or clear program contents once set.
Important notes when using a DSS receiver
•When recording programs via a DSS receiver,
the DSS receiver must be left on.
• When recording programs via an antenna or
cable, the DSS receiver must be turned off.
Push PROG to
dispiay the “SET
PROGRAM" screen.
......... SET PROGRAM -----
VCR PluS+ PROGFiAM
TIMER PROGRAM
Push
AT
to select
“VCR Plus+
^ PROGRAM," and then
^ ^ push ► to dispiay the
“VCR Plus+” screen.
VCR P I U S +
ENTER PLUSCODE NUMBER
si/
/ I \
USING 0-9 KEYS
END :PROG KEY
Push the NUMBERED keys to
enter the PlusCode number.
' Refer to your local TV listings.
To Make Corrections
Push M repeatedly to delete the PlusCode
number. Then, enter the correct number.
VCR P I U S +
ENTER PLUSCODE NUMBER
123456'*
USING 0-9 KEYS
BACKSPACES KEY
ENTER :PROG KEY
Push PROG to lock in
your program.
Push the 1, 2 or 3 key to
select the program type.
To change the recording speed:
Push SPEED for SP, LP or SLP.
To cancel program contents:
Push ADD/DLT.
If you use connection type “A” on page 24, the
on-screen display will always be the cable box
VCR P I U S +
1 ONE TIME
2 DAILY(MON-FRI)
3 WEEKLY
TO SELECT PUSH 1,2 OR 3
DATE START STOP
1:ЮД«И|МДЫ||!1Й
TO CHANGE RECORD SPEED
PUSH SPEED KEY
CANCEL :ADD/DLT KEY
ACCEPTtPROG KEY
channel shown in this
output channel number.
Push PROG
if contents are
acceptable.
P DT START STOP CH SPD
1DAY 9:OOA12:OOA 08 SP
CANCEL;ADD/DLT KEY
SELECT 1-0:A ▼ KEY
ENTER > KEY
END :PR0G KEY
Push PROG to
complete the
program.
If you’re using a Cable Box, make sure
that it is tuned to the desired channel and
the power is left on for timer recording.
TURN VCR OFF
FOR TIMER RECORDING
AND
LEAVE CABLE BOX POWER ON
This display may differ depending
on your cable box hook-up.
Push POWER off
to set the timer.
-ЩШЗ”
Multi Function Display
For a list of publications that carry the PlusCode numbers in your area, call 1 - 800 - 258 - 4827.
You can obtain unlisted PlusCode numbers by calling 1 - 900 - 454 - 7687. Call costs approximately $.95 per minute.
VCR PlusCodes can not be used to program the VCR to record DSS channels.
Avoid overlapping program times.
An on-screen display will indicate if an invalid PlusCode number has been entered or when all timer programs are full.
26