Kontron mITX-E38 - Manual (Page 29)

KTD-N0903-A Page 27 Internal Connectors
mITX-E38 Users Guide
LVDS Flat Panel Connector (LVDS – J31) 7.6
The LVDS connector (Flex boards only) is based on 40 pole connector type Samtec SHF-120-01-F-D-SM-K-
TR or similar.
Note Type Signal PIN Signal Type Note
Max. 0.5A PWR +12V 1 2 +12V PWR Max. 0.5A
Max. 0.5A PWR +12V 3 4 +12V PWR Max. 0.5A
Max. 0.5A PWR +12V 5 6 GND PWR Max. 0.5A
Max. 0.5A PWR +5V 7 8 GND PWR Max. 0.5A
Max. 0.5A PWR LCDVCC 9 10 LCDVCC PWR Max. 0.5A
2K2Ω, 3.3V OT DDC CLK 11 12 DDC DATA OT 2K2Ω, 3.3V
3.3V level OT BKLTCTL 13 14 VDD ENABLE OT 3.3V level
3.3V level OT BKLTEN# 15 16 GND PWR Max. 0.5A
LVDS LVDS A0- 17 18 LVDS A0+ LVDS
LVDS LVDS A1- 19 20 LVDS A1+ LVDS
LVDS LVDS A2- 21 22 LVDS A2+ LVDS
LVDS LVDS ACLK- 23 24 LVDS ACLK+ LVDS
LVDS LVDS A3- 25 26 LVDS A3+ LVDS
Max. 0.5A PWR GND 27 28 GND PWR Max. 0.5A
LVDS LVDS B0- 29 30 LVDS B0+ LVDS
LVDS LVDS B1- 31 32 LVDS B1+ LVDS
LVDS LVDS B2- 33 34 LVDS B2+ LVDS
LVDS LVDS BCLK- 35 36 LVDS BCLK+ LVDS
LVDS LVDS B3- 37 38 LVDS B3+ LVDS
Max. 0.5A PWR GND 39 40 GND PWR Max. 0.5A
Note: The LVDS connector supports single and dual channel, 18/24bit SPWG panels up to a resolution of
1600x1200 or 1920x1080 and with limited frame rate up to 1920x1200.
Signal Description – LVDS Flat Panel Connector:
Signal Description
LVDS A0..A3 LVDS A Channel data
LVDS ACLK LVDS A Channel clock
LVDS B0..B3 LVDS B Channel data
LVDS BCLK LVDS B Channel clock
BKLTCTL Backlight control (1), PWM signal to implement voltage in the range 0-3.3V
BKLTEN# Backlight Enable signal (active low) (2)
VDD ENABLE Output Display Enable.
LCDVCC
VCC supply to the display. 5V or 3.3V (1A Max.) selected in BIOS setup menu. Power
sequencing depends on LVDS panel selection. (Shared with eDP connector)
DDC CLK DDC Channel Clock
Notes: Windows API will be available to operate the BKLTCTL signal. Some Inverters have a limited voltage
range 0- 2.5V for this signal: If voltage is > 2.5V the Inverter might latch up. Some Inverters
generates noise on the BKLTCTL signal, causing the LVDS transmission to fail (corrupted picture on
the display). By adding a 1Kohm resistor in series with this signal, mounted at the Inverter end of
the cable kit, the noise is limited and the picture is stable.
If the Backlight Enable is required to be active high then, check the following BIOS Chipset setting:
Backlight Signal Inversion = Enabled.