Sony SLV-789HF - Manual (Page 8)

step 3: Hookups (continued)
Hpokup¿ H VCR setup
1 Set the RF UNIT switd> to
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set
the switch to either channel.
For details, see page 104.
If you made А/V
connections (from page 9),
you can skip this step.
2 Press EASY SET UP on
the VCR-
O The LANGUAGE menu appears. Change the
on-screcn display language lu Spanish
(ESPAÑOL) or French (HtANgALS) if desired,
and press OK. For details, see page 36.
O The CIOCK SET menu appears. Select AUTO
and press OK. For details, see page ,38.
© The SMART CHANNEL M apping menu
appears. Press to enter the ZliV
POSTAL CODE in your area and press OK. (Yoi
can also use Ute number buttons to enter the
ДР/POSTALCODE.)
O The CABLE BOX CON TROL, menu appears.
5k?lcct OIT and press OK.
0 The TUNER PRESET menu appears. Set
ANTENNA/CABLE to CABIE and press OK.
швшшяваши
For details, sec page 52.
StLECri .[ПП
'^ г - г ЛИ
О Tire AUTO PRESET starts.
Normal display
: Hookup 2 I The VCR Plus+ GOLD system channel setup
SrrjJH
1 Press MENU, then select SETTINGS and press
OK.
2 Select SET VCR Plus+ CHANNELS and press
OK.
3 Select AUTO and press OK.
4 Prc.ss l/Ci) to turn off the VCR.
\Ш1
1 f ■ I Getting Started Getting Started I 17
Step 3: Hookups (continued)
The VCR receives the program infonnation sigr\al from 0;00 am to 5:00 :im
while the VCR is turned off, and set up the channel for the VCR Plus+
GOLD system recording. After channel setup is finished, you can record TV
progranis using the VCR Plus+ GOl.D system. For details, sec page ,39.
Notes
• It takes about 1 hour to complete charrnel setup.
• The VCR can receive the prograin information signal only while the VCR is turned
off and no liinor recordings are set.
• Jf Uie channels in your area don't carry the program information signals, set tlie
program guide channels manually. For details, see page 62.
• If the CHCXl'tSE YOUK CABLE CH MAP menu appears the first time you turn on
the VCR after finishing channel setup, select the MAP number. For details, see
page 61.
Automatic clock setting
Once you've set up the VCR, it automatically sets the clock the first time you
turn off the VCR. After that, whenever you turn off tire VCR, it checks the
time and adjusts the clock, even for Daylight Saving Time. The VCR sets the
clock by picking up a time signal provided by some TV channels.
If you want to use the timer to record right away, or if the channels in yovr
area do not carry time signals, set the clock manually. For details, see
page 43.
Hobkup 3 rPagefr19:to'22 ^
Antenna hookup
Make the following connections if you're using an antenna (if you don'l
have cable TV).
□ Use this hookup if you're using;
• VHF/UHF antenna (you get channels 2-13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
Rear of TV
VHF/UHF
channels 2-13 only) Rear of TV
VHF/UHF Match the type of
■—e A connector on your
TV; A B, or C.
VHF
--t] “
UHF
VHF
—
UHF
For connector types
B and C no UHF
connection is
required.
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a fiat cable (,300-ohm twin lead cable), attach an external
anteniaa connector (not supplied) so you can connect the cable to tl\o VHIVUHi- IN
connector. If you have separate cables for VHi- and UHF antennas, you should use a
U/V band mixer (not supplied) For details, see page ¡05