Sony STR-D1011 User Manual
Fm stereo/fm-am receiver, Son'v, Str-d1011
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Table of contents
Document Outline
- FM Stereo/FM-AM Receiver
- Warning
- Table of Contents
- Overview
- Unpacking
- On safety
- To prevent internal heat buildup in the unit,
- Do not install the unit:
- Do not place anything on top of the cabinet.
- Do not throw away the carton and packing material!
- On operation
- On cleaning the cabinet
- For the customers in the U.S.A.
- Checking the Supplied Accessories
- inserting the Batteries into the Remote Commander
- Selecting the AM Tuning Interval
- Hooking Up the System
- Hooking Up the System
- Identifying the Parts and Controls
- Operating with the Remote Commander
- Adjusting Basic Audio Controis
- Selecting a Program Source
- Selecting a Program Source
- Labeling the Program Source
- Tuning in a Station Directly (Direct Tuning)
- Automatic Tuning
- Presetting Stations (Station Preset)
- Labeling the Preset Stations (Station Index)
- Tuning in a Preset Station (Preset Tuning)
- Selecting a Station among the Preset Stations in the Index (Index Tuning)
- Receiving FM Simulcast TV Programs
- Recording an Audio Source
- Recording onto an Audio Tape Deck or DAT Deck
- Tape Dubbing
- 1 Select the desired program with the FUNCTION buttons.
- Set the tape (DAT) deck in the recording mode.
- Start playback of the selected program source.
- Monitoring the recorded sound
- 1 Insert the recorded tape into tape deck 1 (or the DAT deck).
- 2 Insert a blank tape into tape deck 2 and adjust the recording level.
- 3 Press TAPE 1 or DAT to select the deck for playback.
- Note on tape dubbing
- Editing a Video Source
- Video Tape Dubbing
- Select the playback VCR with EDIT VIDEO.
- Press VIDEO 2 or VIDEO 3 to select the video signal to monitor on the monitor TV according to the VCR to be played.
- Set the playback VCR to the playback mode.
- 4 Set the VCR 1 to the recording mode.
- — Video Tape Editing —
- To switch the playback VCR during dubbing
- To view the other video source(s) on the monitor TV during dubbing
- To listen to an audio program during video tape dubbing
- Video Tape Dubbing
- Editing a Video Source
- Adding New Sound on a Video Tape during Video Editing
- Select the playback. VCR with EDIT VIDEO.
- Set the playback VCR to the playback mode.
- At the point where audio dubbing starts, press the pause button on the playback VCR.
- Press EDIT AUDIO.
- Select the audio program source.
- Release the pause mode of the playback VCR and set the VCR 1 to the recording mode.
- Start playback of the selected audio program source.
- Adding New Sound on a Video Tape during Video Editing
- What Is the Digital Signal Processor
- Sound Field Setting
- Getting Ready for Dolby Surround Sound
- Getting Ready for Dolby Surround Sound
- Adjusting the Speaker Volume
- Adjusting the Delay Time of the Rear Speakers
- Understanding the Digital Surround Processor
- Characteristics of the SOUND FIELD program
- Adjusting the Surround Effect
- Press the desired SOUND FIELD program.
- 3 Press CURSOR MODE to select the SUR (surround) mode.
- Press Л or V to select the desired parameter.
- Adjust the parameter by pressing .
- When you store a new SOUND FIELD effect
- Even if AC power cord is disconnected
- When selecting ACOUSTIC
- Tips for adjusting the main parameters
- I Wall Material Simulation
- I Seat Position Simulation
- ■ Reverberation Time
- Understanding the Digital Parametric Equalizer
- How to Adjust the Digital Parametric Equalizer
- Enjoying with Your Private Setting
- Specifications
- Quick Reference
- Quick Reference