Dell PowerEdge 650 - Manual (Page 23)

BIOS Update Attempt
Failed!
Remote BIOS update attempt failed. Retry the BIOS update. If the problem persists, see " Getting Help ."
Caution! NVRAM_CLR
jumper is installed on
system board. Please
run SETUP
Incorrect configuration settings in
System Setup program; NVRAM_CLR
jumper is installed; faulty system
battery.
Check the System Setup configuration settings. See "Using the System Setup Program" in
your User's Guide. Remove the NVRAM_CLR jumper. See Figure A -2 for jumper location.
Data error
Faulty diskette, diskette drive, CD
drive, or hard drive.
Replace the diskette. Ensure that the diskette/CD-drive subsystem and hard drives are
properly installed. If the problem persists, replace the diskette/CD-drive subsystem. See
"
Removing the CD and Diskette Drives " in "Installing Drives." If the problem persists,
replace the faulty hard drive. See " Hard Drives " in "Installing Drives."
Decreasing available
memory
Faulty or improperly installed memory
modules.
Ensure that all memory modules are properly installed. If the problem persists, replace
the memory module(s). See " Removing Memory Modules " and " Installing Memory Modules "
in "Installing System Components."
Diskette drive 0 seek
failure
Incorrect configuration settings in
System Setup program.
Run the System Setup program to correct the settings. See "Using the System Setup
Program" in your User's Guide.
Faulty or improperly installed
diskette, loose diskette/CD interface
cable, or loose power cable.
Replace the diskette. Ensure that the diskette/CD-drive subsystem is properly installed. If
the problem persists, replace the diskette/CD-drive subsystem. See " Removing the CD and
Diskette Drives " in "Installing Drives."
Diskette read failure
Faulty or improperly inserted diskette. Replace the diskette.
Diskette subsystem
reset failed
Faulty diskette/CD-drive controller. Ensure that the diskette/CD-drive subsystem is properly installed. If the problem persists,
replace the diskette/CD-drive subsystem. See " Removing the CD and Diskette Drives " in
"Installing Drives." If the problem persists, see " Getting Help ."
Diskette write
protected
Diskette write-protect feature
enabled.
Move the write-protect tab on the diskette to disable the write-protect feature.
Drive not ready
Diskette missing or improperly
inserted in diskette drive.
Reinsert or replace the diskette.
Embedded server
management error
Faulty or improperly installed remote
access card, or loose cable
connection.
Ensure that the remote access card's cable is properly connected. Ensure that the remote
access card is properly installed. See " Expansion Cards " in "Installing System
Components." If the problem persists, replace the remote access card. If the problem
persists, see "
Getting Help ."
Embedded server
management is not
present
Remote access card not installed,
improperly installed, or faulty.
Ensure that the remote access card is installed and installed properly. See " Expansion
Cards " in "Installing System Components." If the problem persists, replace the remote
access card. If the problem persists, see " Getting Help ."
Error: More than one
RAC detected, system
halted.
Two remote access cards are
installed, or faulty or improperly
installed remote access card.
Ensure that there is only one remote access card installed and that it is installed in the
upper slot. Ensure that the remote access card is properly installed. See " Expansion
Cards " in "Installing System Components." If the problem persists, replace the remote
access card. If the problem persists, see " Getting Help ."
Error: Remote Access
Card initialization
failure.
Faulty or improperly installed remote
access card.
Ensure that the remote access card is properly installed. See " Expansion Cards " in
"Installing System Components." If the problem persists, replace the remote access card.
If the problem persists, see "
Getting Help ."
Error: RAC is not in
the correct PCI slot,
system halted.
Remote access card not installed in
the proper PCI slot.
Ensure that the remote access card is installed in the upper slot.
Error: RAC cannot be
used with an add-in
video card in this
slot.
Add-in video card is installed. Remove the add-in video card. See " Removing an Expansion Card " in "Installing System
Components." To use the add-in video card, remove the remote access card.
Gate A20 failure
Faulty keyboard controller (faulty
system board).
See " Getting Help ."
General failure
Operating system corrupted or
improperly installed.
Reinstall the operating system.
Hard disk controller
failure
Incorrect configuration settings in
System Setup program.
Run the System Setup program to correct the settings. See "Using the System Setup
Program" in your User's Guide.
Faulty or improperly installed hard
drive, or loose power cable.
Ensure that the hard-drive subsystem is properly installed. If the problem persists,
replace the faulty hard drive. See " Hard Drives " in "Installing Drives."
Memory module installation guidelines
have not been properly followed.
Ensure that the memory modules are properly populated. See " Memory Module
Installation Guidelines " in "Installing System Components."