SARGENT 351 Series Aluminum Closer - Manual

SARGENT 351 DOOR CLOSERS
WITH CPS/CPSH ARMS
INSTALLATION INSTRUCTIONS
351 ADJUSTABLE FROM SIZE 1 THRU 6
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR ASSISTANCE CALL SARGENT AT 1-800-727-5477.
1
DETERMINE MAXIMUM DEGREE OF OPENING OR HOLD OPEN (CPSH) REQUIRED. DRILL AND TAP DOOR AND FRAME FOR
#12-24 MACHINE SCREWS. WHEN USING SELF TAPPING SCREWS PROVIDED, PREDRILL WITH A 3/32" DRILL.
PULL SIDE PULL SIDE
PUSH SIDE PUSH SIDE
LEFT HAND DOOR RIGHT HAND DOOR
CLOSERS ARE NON-HANDED
2
A7345B
1
13/16"
CENTERLINE
OF
HINGE
“A”
1-15/16"
2-11/16"
13/16"
5/16"
3-1/16"
3-7/8"
1-7/8"
9/16"
5/8"
9"
2-5/8"
2-1/2"
CENTERLINE
OF
HINGE
“B”
(FROM STOP)
DEGREE OF DOOR OPENING AT “HOLD OPEN”
■
85° 90° 95° 100° 105° 110°
DIM. “A” 9-1/2" 8-3/4" 8-1/8" 7-9/16" 7-1/16" 6-5/8"
DIM. “B” 10-3/16" 9-7/16" 8-13/16" 8-1/4" 7-3/4" 7-5/16"
■ DIMENSIONS FOR GIVEN DEGREE BASED ON 4-1/2" HINGE. WHEN 3-1/2"
TO 6" HINGES ARE USED, HOLD OPEN ANGLE WILL CHANGE BY LESS
THAN 1/2°. DEAD STOP OCCURS 3° BEYOND HOLD OPEN.
IMPORTANT NOTICE
PRE-DRILL 3/32"
HOLES FOR SELF-
TAPPING SCREWS
OR TAP #12-24 FOR
MACHINE SCREWS
A7345B
4
+
or
RH
SPRING
ADJUSTMENT
NUT
INSTALL DOOR CLOSER TO DOOR WITH SPRING
ADJUSTMENT NUT AWAY FROM HINGE.
NOTE:
351 CLOSER BODIES ARE NON HANDED. IT
IS IMPORTANT THAT THE CLOSER BODY IS
INSTALLED WITH “RH” SYMBOL AT TOP FOR
RIGHT HAND DOORS, “LH” SYMBOL AT TOP
FOR LEFT HAND DOORS.
MOUNT FOOT BRACKET TO DOOR STOP.
BUMPER & HOLDER
12-24 x 1" MS or
#12 x 1-3/4"
12-24 x 1-3/4" MS
or #12 x 2-1/2"
4 #12-24 x 5/8" MS
or #12 x 1-3/4"
INSERT
“CPSH” ONLY
RH CPSH
SHOWN
3B 1/2"
7/8"
5/8"
CPSH SHOWN
CPS SIMILAR
IMPORTANT: USE A MINIMUM
OF 7 SCREWS.
USE SPACER
WHEN REQUIRED
3C ALTERNATE:
PREASSEMBLE ARMS
PRIOR TO ATTACHING
TO STOP.
ARM MUST BE THE SAME HAND AS THE DOOR. ASSEMBLE THE
HOLDER WITH BUMPER & INSERT (CPSH ONLY) TO FOOT
BRACKET AS LOCATION OF THESE PARTS DETERMINES THE
“HAND”. 3A
Copyright © 2005, 2008, Sargent Manufacturing Company, an ASSA ABLOY
Group company. All rights reserved. Reproduction in whole or in part without the
express written permission of Sargent Manufacturing Company is prohibited.
Copyright
©
2005, 2008, Sargen
t Manufacturing Company
, an A
SS
A
ABL
O
Y
Group company
. All right
s reser
ved. Reproduction in whole or in par
t without the
express writ
ten permission of Sargen
t Manufacturing Company is prohibited.