Opticon H19 car kit Quick Guide - Manual

Quick Start Guide
• Read this quick start guide carefully before installing or/and using the cradle.
• Keep this quick start guide for future reference and store in a safe place.
Introduction
CAUTION
• This quick start guide may be revised or withdrawn at any time without prior notice.
• This quick start guide may not, in whole or in part, be copied, photocopied, reproduced, translated or
converted to any electronic or machine readable form without prior written consent of Opticon.
• Trademarks used are property of their respective owners.
• Under no circumstances shall Opticon be held responsible for any special, incidental, consequential or
indirect damages howsoever caused.
Handling Instructions
• The H19 Vehicle Cradle is a designated vehicle mount cradle for the H19 smartphone portable terminal.
• Determine the best position of the cradle and ensure it does not obstruct your vehicle controls.
• Position the cradle taking in consideration the driver field of view and does not obstruct the driver’s view.
• Place the H19 cradle to ensure proper ventilation around the device.
• Do not operate the unit while driving.
• Any modification to the mounting pedestal not expressively approved by Opticon could void the user’s
authority to operate the equipment.
• Do not install the vehicle cradle over an air bag cover or within the air bag deployment zone.
• Attach the pedestal suction cup onto a smooth surface like the glass windshield. (Clean the mounting surface
before attaching the base of the cradle)
H19
Vehicle Cradle
Using the Cradle
STEP 1
Insert the H19 into the
Vehicle Cradle as shown.
STEP 1-1
Rotate the restraining
bracket over the top of
the H19.
STEP 1-2
Firmly slide the cradle onto the arm until it clicks.
STEP 1-3
STEP 2
Please attach the Vehicle Cradle onto a smooth surface like the glass windshield.
(Be sure to clean the mounting surface before attaching the base of the Vehicle Cradle.)
With the Vehicle Cradle oriented as shown in the
diagram, firmly press the base of the Vehicle Cradle
against the mounting surface.
STEP 2-1
Adjust the height or the angle of the Vehicle Cradle
using the knobs as shown in the diagram.
STEP 2-3
Rotate the activating lever upward as indicated in
the diagram.
STEP 2-2
H19
Cradle
Restraining Bracket
Lever
Knob A
Knob B
The Netherlands Opticon Sensors Europe B.V.
tel: +31 (0)23-5692700 / email: [email protected]
U.S.A. Opticon Inc.
tel: 800-636-0090 / email: [email protected]
France Opticon S.A.S.
tel: +33 (0)1-41461260 / email: [email protected]
Germany Opticon Sensoren GmbH
tel: +49 (0)6074-91890-0 / email: [email protected]
Italy Opticon s.r.l.
tel: +39 (0)051-6321800 / email: [email protected]
Spain Opticon Sensores S.L.
tel: +34 (0)902-747469 / email: [email protected]
Contact
Sweden Opticon Sensors Nordic AB
tel: +46 (0)8-58548560 / email: [email protected]
United Kingdom Opticon Limited
tel: +44 (0)1582-635100 / email: [email protected]
Taiwan Opticon Far Eastern Ltd.
tel: +886 2-27597444 / email: [email protected]
China Opticon Sensors Europe B.V., Shanghai Representative Office
tel: +86 21-64480881 / email: [email protected]
Australia Opticon Sensors Pty. Ltd.
tel: +61 (0)2-43402666 / email: [email protected]
Brazil Opticon Sensors Europe B.V., Latin American Office
tel: +55 11-8322 2244 / email: [email protected]
Please contact Opticon or your local dealer.
Copyright 2007, Opticon All rights reserved.
Optional Parts A pedestal suction cup available
Accessories & Optional Parts
Overview
The H19 Vehicle Cradle consists of 3 major sections: cradle section, arm section and a cable.
The following two tables show the physical features of the cradle section and the arm section.
Dimensions (H) 95 × (W) 69 × (D) 48 mm Max
(H) 3.74 × (W) 2.72 × (D) 1.89 in. Max
Weight 60 g (2.12 oz / 0.13 lb)
Cradle Section Arm Section
Dimensions (H) 125 × (W) 80 × (D) 80 mm Max
(H) 4.92 × (W) 3.15 × (D) 3.15 in. Max
Weight 120 g (4.32 oz / 0.26 lb)