Opticon H16 Quick Guide - Manual

1 Soft key 1 Performs the command shown in the label above the button
2 QWERTY keyboard A hardware keyboard similar to a standard one on your PC
3 Soft key 2 Performs the command shown in the label above the button
4 Scan key (Left) Press the key to scan and decode bar code/2D code
5 Record key Press and hold this key to record a voice note
6 Volume up Press the Volume up button to turn up the PDA receiver volume
7 Volume down Press the Volume down button to turn down the PDA receiver volume
8 RESET button Press the RESET button with stylus to soft-reset your device
9 Eyelet for wrist strap(Left) Fix a wrist strap here
10 Stylus Write, draw, or make selection on the touch screen
11 Scanner Point the reading window of the scanner in the direction of bar code/ 2D code
12 Power button Power on or off the device
13 Wi-Fi/Bluetooth LED Indicates Wi-Fi/Bluetooth Status
14 Telephone receiver Listen to a phone call here
15 GSM/Battery LED Indicates GSM/Battery LED
16 Display 2.8-inch TFT LCD with touch screen
17 Soft key 3 Performs the command shown in the label above the button
18 Soft key 4 Performs the command shown in the label above the button
19 Start key Pull down the Start menu
20 OK key Press OK key to make a selection
21 Talk key Press this key to dial or answer a call
22 5-way navigation key
Press this button up, down, left, or right to move through menus; carry out the selec-
tion by pressing the center button.
23 End key End a call or close Phone application
24 Speaker Listen to audio media or listen to a phone call hands-free
25 Battery pack Remove to place battery and SIM card
26 Microphone Speak into the microphone when talking on the phone or recording a voice note
27 Scan key(Right) Press the key to scan and decode bar code/ 2D code
28 Eyelet for wrist strap(Right) Fix a wrist strap here
29 Mini-SD card slot Insert a mini-SD card to expand device memory
30 Mini USB connector Mini USB connector for PC sync and battery charging
31 Earphone Jack Connect a 2.5 mm Earphone
a AC Adapter Recharge the device battery
b Stereo Headset Listen to a phone conversation hands-free
c USB Cable Connect the device to a PC
d Getting Started CD Windows Mobile TM Getting Started Disc
e User Manual/Quick Guide Provide instructions of device functions
f Pouch Protect the device
g Battery Rechargeable Li-ion polymer battery
h Stylus Write, draw, or make selection on the touch screen
The “Fn” key is used to access the symbols in blue on the keypad. Press this key once and the icon
appears; the next character you enter will be a symbol or number (for example: @abc). Press the “Fn”
key twice can enter numbers and symbols constantly (for example: $25). You can also hold down the “Fn”
key and press another key at the same time to enter its corresponding symbol.
Press this key once, the next character you enter will be a capital letter (for example: Abc). Hold down
this key and press another key at the same time to enter capital letters constantly. Alternatively, you can
press the “Fn” key once and then press this key ( appears) to enter capital letters constantly. For
returning to enter lowercase letters, press the “Fn” key and then the “Cap” key.
Press this key to erase the letter in the left side of the cursor. Press the “Fn” key once ( appears)
then press this key to delete the first letter in the right side of the cursor. To disable the “Fn” key, press it
again ( will disappear).
You can press this key to enter symbols or special characters such as accented letters (e.g. а, й…etc.).
After pressing a character, press the “Fn” key and then the “Sym” key once to show an accent type of
this character. To show another accent type, repeat the same steps until the desired type is displayed.
See page 27 in the user manual for corresponding symbols for each character/key.
Views of the Device
4
8
9
5
6
7
1
2
3
10 11 12
17
19
21 18
20
23
16
13 15
14
26
22
24
25
29
31
30
28
27
Accessories
To enter capital letters/numbers, or to delete/backspace by using the
hardware keyboard:
Hardware Keypad / Installing SIM Card and Battery
a
c
Quic
k Guide
Quic
k Guide
Manual Manual
d
e
f
g
h
b
Installing the SIM Card
If you want to use phone features, you must install
a GSM SIM card.
•Push upper corners and slide down the battery
cover to remove it.
•Place the SIM card in the SIM card slot with the
gold contacts facing down. The SIM card’s cut-
off corner should match the cut-off corner in the
SIM card slot.
Installing the Battery
•Press the battery down forcefully into the battery
slot and close the back cover.