Unp 500, Setup, 6 programme mode – Memmert ICH/ ICH L Climate chambers User Manual
Page 29: Starting a programme, Manual mode
D30381 | Date 10/2014
29
Operation and control
3. Press the confirmation key to confirm.
Hauptschalter
>
Zu der Typenbezeichnung gibt es momentan drei Entwurfsrichtungen,
ich kann Ihnen noch nicht sagen, ob Memmert hierzu schon eine Entscheidung
getroffen hat.
Die hier gezeigt Variante, ist die von uns empfohlene Richtung.
UF 110
PLUS
ON
344
.4
444
4
.
TEMP
Set
°C
°C
FLAP
40
%
TIMER
h
d
10
02
End
Sept.
29
22 24
FAN
%
0
%
100
ALARM
max
444
.4°C
auto
+/-
0.0
K
min
444
.4°C
O
O
ON
N
N
N
O
O
N
O
Manu
44.Sept
The display now shows the remaining time
in a large font and the approximate end time
in a smaller font beneath. The status display
shows „Timer active“.
TIMER
30
m
04
h
Ende 13:30 23.11.
Timer active
12.Sept.2012 13:44
4. Now, as described under 5.4.4, set the individual values for temperature, air flap position
etc. which you want the appliance to operate at. The set values can be changed at any
time during the timer. The changes are effective immediately.
In
Setup
, you can choose if the timer should run setpoint-dependent or not. This deter-
mines whether the timer should not start until a tolerance band around the set tempera-
ture is reached or if it should start right after activation (see page 46). If the timer runs
setpoint-dependent, this is indicated by the
symbol in the timer display.
When the timer has elapsed, the display shows 00h:00m. All func-
tions (heating etc.) are switched off. In addition, an acoustic alarm
sounds, which can be turned off by pressing the confirmation key.
To deactivate the timer, open the timer display by pressing the
activation key again and then turning the turn control to reduce
the timer setting until --:-- is displayed. Confirm with the confirma-
tion key.
5.4.6 Programme mode
In this operating mode, programmes saved in the appliance can be started with different
combinations of individual parameters (temperature, humidity, interior lighting) at staggered
intervals, which the appliance then automatically processes in sequence. These programmes
are not created directly at the appliance but externally at a computer / laptop and using
AtmoCONTROL software. Transfer to the appliance is possible using the provided USB storage
medium or via Ethernet.
A description of how to create and save programmes can be found in the separate
AtmoCONTROL software manual.
Starting a programme
Starting a programme
1. Press the activation key to the right of
the status display. The current operating
mode is highlighted automatically, in this
example
manual mode
(
).
UNP 500
344
.4
444
4
.
TEMP
Set
°C
°C
LIGHT
100
%
manueller Betrieb
FLAP
40
%
.4
444
4
.
TEMP
Set
°C
°C
FLAP
%
LIGHT
%
TIMER
End
--
--
m
h
- -
- -
- - - - -
Fr 20.10.2010 20:31
ALARM
min
100°C
max
400°C
auto off
+/- 0.0K
0
8
16
40
80
GRAPH
0
8
16
40
80
GRAPH
APH
Manual mode
17:44
13.Sept.2012
Activate
TIMER
00
m
00
h
End 13:30 23.11.
TIMER
--
m
--
h
End 9:00 23.11.